Committee of Testing Laboratories  |
|---|
| CTL HOMEPAGE | ABOUT THE CTL | DECISION SHEETS | TESTING LABS |
| TESTING EQUIPMENT | PROFICIENCY TESTING | ETFs AND WORKING GROUPS | OPERATIONAL PROCEDURES |
| Clause | Subject | Keywords | Sheet |
| General | General | - validity of the decisions | OSM/HA 0 |
| Procedure | Procedure | - series of models | OSM/HA 07 |
| Procedure | Procedure | - country of origin - CCA-NTR |
OSM/HA 184 |
| Procedure | Procedure | - Test report form | OSM/HA 185 |
| Procedure | Procedure | CCA-NTR for components | OSM/HA 187 |
| General | Procedure | - Components - Certificates |
OSM/HA 40 |
| General | Mandatory additional information (details) in Test Report | - additional information; - details; - Test Report |
OSM/IN 248 |
| IEC 60238 Ed.5 | |||
| Clause | Subject | Keywords | Sheet |
| - | Edition of the gauge
sheet, when testing lampholder |
- gauge - lampholder |
258.CTL-ETF5 |
| IEC 60238 Ed.6 | |||
| Clause | Subject | Keywords | Sheet |
| 4.9.2 | Lampholder to be
built into ovens |
- oven | 268.CTL-ETF5 |
| IEC 60238 Ed.7 | |||
| Clause | Subject | Keywords | Sheet |
| Figure 17 | Protection against ingress of water | -
Drop of liquid - Holes of equipment - Ingress of water |
398.CTL-ETF5 |
| IEC 60238/2002 | |||
| Clause | Subject | Keywords | Sheet |
| General | Gauges | -
Gauge - Test Report - IEC 60061 |
207.03.OSM |
| General | Lampholder to be built into ovens | -
IEC 60238 - Ovens - IEC 335.2.6 |
208.03.OSM |
| 12.1 | Test method for checking with "feeler gauge" | -
Feeler gauge - Circular direction - Lamp caps |
210.03.OSM |
| IEC 60309-2:1999 | |||
| Clause | Subject | Keywords | Sheet |
| 12.3 | Measurement of height of retaining means for IP44 socket-outlets and connectors | - Retaining means | OSM/IN 201 |
| 16.101 – 17.101 | Construction of pins of plugs and appliance inlets | - pin - electroplated coating |
OSM/IN 244 |
| IEC 60400 Ed.4 | |||
| Clause | Subject | Keywords | Sheet |
| - | Edition of the gauge
sheet, when testing lampholder |
- gauge - lampholder |
258.CTL-ETF5 |
| IEC 60400/2002 | |||
| Clause | Subject | Keywords | Sheet |
| General | Gauges | -
Gauge - Test Report - IEC 60061 |
207.03.OSM |
| 2.3 | Push-on lampholders | - Push-on lampholder - Tubes - Live parts |
211.03.OSM |
| 8.2 | G10q connector's construction | - G10q lampholder - Protection against electric shock - Connector's construction |
PDSH.12.04.OSM |
| IEC 60570/2003 | |||
| Clause | Subject | Keywords | Sheet |
| General | Openings for the adapters | -
Construction - Openings - Adapters |
202.03.OSM |
| General | Connector with a flexible cord and a normal plug | -
Connector - Flexible cord - Contacts |
203.03.OSM |
| 1 | Luminaires with socket outlet connected to track system | -
Socket-outlet - Track system - Luminaires |
204.03.OSM |
| 2.3.3.9/ 5.13 | IP 40 indication | -
Common conclusion - IP 40 indication - L.I.P. |
205.03.OSM |
| 12 | Extra safety circuit equivalent to SELV or double/reinforced insulation | -
SELV condition - Electronic means -IEC 60364-4-41 IEC 61140 |
206.03.OSM |
| IEC 60598-1/1996 IV Ed | |||
| Clause | Subject | Keywords | Sheet |
| 0.2 | - Socket-outlet mounted rechargeable luminaire - Rechargeable lamps luminaire |
- Socket outlet - Transformer/Plug - Battery chargers |
006.03.OSM |
| 4.14.3 | Screw adjustable by the user | - Instruction manual - more than 360° - User |
065.03.OSM |
| 11.2.1 | Pendant luminaire
with a "ceiling cone" |
- Mounting surface - Supply wires - Ceiling cone |
120.03.OSM |
| IEC 60598-1/1999 V Ed. | |||
| Clause | Subject | Keywords | Sheet |
| General 1.7 |
Fixed luminaire with track | -
IEC 60570+A1/A2 - 6,5 mm - Track system |
004.03.OSM 004.03.OSM.Figure |
| 0.2 | - Socket-outlet mounted rechargeable luminaire - Rechargeable lamps luminaire |
- Socket outlet - Transformer/Plug - Battery chargers |
006.03.OSM |
| 0.3.1 | Portable floodlights/lighting chains IP44 |
- Plug - Full - profile - IMQ questionnaire |
007.03.OSM |
| 0.4 | Floodlight with mounting accessories |
- Floodlight - Mounting accessories - Part of installation |
012.03.OSM 012.03.OSM.Figures |
| 0.4.2 | Range of luminaires | - Range - N.C.B. - Test Reports |
008.03.OSM |
| 0.4.2 | Range of luminaires | - Working group - Range of luminaires - Experience |
009.03.OSM |
| 0.4.2 | Range of luminaires | - Fluorescent lamps - Same lampholder - Discharge lamps |
009A.03.OSM |
| 0.4.2 | Instruction manual
of a floodlight |
- Mounting instructions - Unfavourable - Instructions manual |
013.03.OSM |
| 0.4.2 General | Luminaires needing assembly by the user | - Common sense - Easiness of connection - Pendant luminaires |
011.03.OSM |
| 0.4.2 | Luminaires needing reconnection by the installer | -
Reconnection - Extra terminal - Different voltages or wattages |
260.03.OSM |
| 0.5 | Use of 230V components in 240V luminaires | - UK - 230 V, 240 V - Rated voltage |
014.03.OSM |
| 0.5 | Series - compensated luminaire (working voltage) | - Series capacitors - 450 V - Working voltage |
015.03.OSM |
| 0.5 | Connecting device
with fuse holder |
- Fuse holder - Connecting device - Fuse |
018.03.OSM |
| 0.5 | External cable | - Cable or cord - Wiring - Luminaires Standards |
019.03.LIP |
| 0.5 | Luminaire marked for lamp GU 5,3 | - EPCAP Group - GU 5,3 - GX 5,3 connector |
020.03.OSM |
| 0.5 | AC supplied electronic ballasts for discharge lamp luminaires |
- IEC/EN 61347-2-1 - IEC/EN 61347-2-3 - IEC 61347-2-9 §§ 1 -2-7 |
021.03.OSM |
| 1.2 | Interconnecting cables | -
8 cm - 0.75 mm.sq - Internal wiring |
022.03.LIP |
| 1.2.24 | Class III luminaire | - Non-detachable - Transformer - SELV |
023.03.OSM |
| 3 | Definition of basic
type reference |
- Rated wattage - Type reference - Separately marked |
024.03.OSM |
| - | Marking
on class III luminaires "system" |
-
Connecting device - Each connection - Marking |
261.03.OSM 261.03.OSM.figures |
| 3.2.2 | Rated voltage marking | - Filament lamps - Rated voltage - Marking |
026.03.OSM |
| 3.2.6 | Term "If applicable" | - IP 20 - Luminaire other than ordinary - If applicable |
027.03.LIP |
| 3.2.6 / 9.2 | IP test on recessed luminaires | -
Test recess - Fixed luminaire - Recessed luminaire |
028.03.OSM |
| 3.2.6 | Marking with IP numbers | - IP marking - Mounting orientations - Type designation |
252.03.OSM |
| 3.2.13 | Symbol for minimum distance from lighted objects |
- Temperature - Lighted object - Distance symbol |
030.03.OSM |
| 3 | Markings / additional information |
- Proper installation - Safety - Markings |
262.03.OSM |
| 3.3.7/4.24 Annex P |
UV radiation | -
Protected shield - UV blocked lamp - Mounting height |
031.03.OSM |
| 4.12.4/4.6 | mechanical connections lampholder between different parts of luminaire | - electrical connections strain cord anchorage | 523.OSM/CTL-ETF5 |
| 4.2 / 15.7 | Non-detachable flexible cable or cord |
- Component - Conductors - Cable or cord |
032.03.OSM |
| 4.2 / 8.2.1 | Luminaire with fuse holder/fuse |
- Entrance - Tool - Marking |
033.03.OSM |
| 4.4 | Non standardised lampholder |
- Miscellaneous lampholder - IEC 60838-1 - Built-in / integral |
034.03.OSM |
| 4.4.4 | Lampholder fixed by the shade ring | - Luminare
standards - Lampholder - Shade ring |
035.03.OSM |
| 4.4.4 ii) | Lampholder mounting brackets | - Lampholder - Safety - Compliance |
036.03.OSM |
| 4.7.2 | Supply terminals (8 mm free wire) | - Figures 1, 2, 3 - Correct way - Both wires stripped 8mm |
037.03.OSM 037.03.OSM.Figures |
| 4.7.3 | lampholder terminals | - Screwless terminal - Rewirable luminaire - Solid/flexible conductors |
038.03.OSM |
| 4.7.4 | Terminals for internal and external connections | - Internal connections - Supply connection - Internal wiring |
039.03.OSM |
| 4.8 | switches for luminaires | - Switches - 10.000 cycles - IEC 61058-1 |
040.03.OSM |
| 4.8 | electronic switches | - Electronic Switch - LUMEX - IEC 61058-1 |
041.03.LIP |
| 4.10 | Insulation required for external and SELV wiring | - Basic insulation - Double/reinforced insulation - Wiring |
042.03.OSM |
| 4.10.1 | metal suspension device | - Suspension device - Metal hook - Fixed installation |
043.03.OSM |
| 4.10.1 | Sleeves of insulating material | - Sleeves - Fixed wires - Inside the luminaires |
045.03.OSM |
| 4.10.1 | double and reinforced insulation | - Enclosure - Mounting Surface - Live Parts |
046.03.LIP |
| 4.11 / 4.12 | luminaires to be assembled by user | -
User - Earth connection - Ready-made plugs and connectors |
048.03.OSM |
| 4.11.1 | contact pressure | -
Construction - Each case - Touch lamp |
047.03.OSM |
| 4.11.3 | locking device for screws | - Locking device - Mechanical connections - Fixing screws |
050.03.OSM |
| 4.11.3 | Electrical connections | -
Construction - Connections - Locking device |
053.03.OSM 053.03.OSM.Figures |
| 4.11.3 | Screw connections | - Small "spikes" - Locking of screw connections - Ballast |
052.03.OSM 052.03.OSM.Figure |
| 4.11.3 / 7 | Crimped connections | -
Relevant tests - Crimped connections - Mechanical / electrical contacts |
054.03.OSM 054.03.OSM.Figures |
| 4.11.3 / 7.2.4 | Rivets for electrical and mechanical connections | - rivets - earthing connections - accidental loosening |
051.03.OSM |
| 4.11.4 | Material with equivalent characteristics | - Material - Equivalent characteristics - Conductive material |
055.03.OSM |
| 4.12.4 | Portable luminaire; different parts can be loosen by hand | -
Middle pipe - Adequate means - Clause 4.12.4 |
057.03.OSM |
| 4.11.5 | Wooden parts on luminaires | - Wooden parts - Contact with current carrying parts - Supplementary insulation |
056.03.OSM |
| 4.13.1 | Mechanical strength | - Mechanical strength - Light source - Not performed |
058.03.OSM |
| 4.13.1 | Mechanical strength | -
Three impacts - Weak points - Sample |
059.03.OSM |
| 4.14 | Suspension devices | - Additional weight - Point B and/or C - Design |
060.03.OSM 060.03.OSM.Figure |
| 4.14 | Suspension devices for recessed luminaire | - Fixed luminaires - Fixing devices - Test A |
061.03.OSM |
| 4.14.1 | Clip-mounted luminaire | - Clip-mounted luminaire - Unfavourable condition - Normal use |
062.03.OSM |
| 4.14.1 | Clip-mounted luminaire: pulling test | - Clip-mounted luminaire - No movement - Unfavourable direction |
063.03.OSM 063.03.OSM.Figure |
| 4.14.2 | Suspended luminaire | -
Flexible cables - Weight - Mass of the luminaire |
064.03.OSM |
| 4.14.3 | Screw adjustable
by the user |
- Instruction manual - More than 360° - User |
065.03.OSM |
| 4.15 12.7.1 |
Application of clauses 4.15 and 12.7.1 | - Ballast - Plastic Enclosure - Metal "Body" |
067.03.LIP |
| 4.15 12.7.1 |
Application of the linear regression formula | - Both materials - Thermo-resisting bush - Thermoplastic body |
068.03.LIP |
| 4.15 a) | Luminaires in thermoplastic material (fixing points) | -
Ballast - Constructive measures - § 4.15 a) / § 12.7.1 |
248.03.OSM 248.03.OSM.figure1 248.03.OSM.figure2 |
| 4.15 | Flammable materials | - Ignition temperature - Life time - Glow wire test |
264.03.OSM |
| 4.15 | Heated part | - Light sources - Ballasts - Transformers |
265.03.OSM |
| 4.16 | Temperature sensing control device | - Reproducibility - Additional fixing - Ballast or transformer |
069.03.OSM |
| 4.16.2 / 12.6.2 | "Temperature sensing controls" | - Temperature sensing device - PTC or fuse - Transformer and ballast |
070.03.OSM |
| 4.21.3 | Luminaires with R7s lamp cap | - Lamp compartment - Present standard - R7s lamp cap |
071.03.OSM |
| 4.21.3 | Impact test on shields | - Impact Test - Outside of the shield - Table 4.3 |
072.03.LIP |
| 4.24 | Annex P | - Lamp manufacturers - Information - Case by case |
073.03.OSM |
| 4.24 | Annex P | - Data - Manufacturer - Procedure A |
074.03.OSM |
| 4.24 | Use of different M.H. lamps | - ILCOS code - Rated current - New lamp |
075.03.OSM |
| 4.24 | Protective shield | - LUMEX - Lamp manufacturers - Technical information |
076.03.OSM |
| 5.2 | Interconnecting cables | -
8 cm - 0.75 mm.sq - Internal wiring |
022.03.LIP |
| 5.2 | Non standardised plug for class III luminaire | -
Sub clause 4.11.6 - Marking - Rated current |
078.03.OSM |
| 5.2.2 | Insulation required on a cable (SELV operating) | - Basic insulated
parts - SELV - Cable H03VH-H |
079.03.OSM |
| 5.2.2 | External wiring for low voltage luminaire | - Sub-Clause 5.2.2 - Standard - External wiring |
080.03.LIP |
| 5.2.2 5.3.5 |
Internal wiring | - Internal cable - Cord anchorage - Cable Length |
081.03.LIP |
| 5.2.2 / 7.2.11 | Transparent flexible cords | - Transparent cable - Earth wire - Green/yellow |
082.03.OSM.LIP |
| 5.2.2 5.3.3 |
Push fit bushes | - Push
fit bushes - Properly sized - Standard |
083.03.LIP |
| 5.2.10 | Cord anchorage construction | - Movement - Pushing the cable - Relevant requirements |
084.03.OSM |
| 5.2.10 / 5.3.5 | Cord anchorage on lampholder |
- Class I / II /
III - Live parts - Lampholder |
086.03.OSM |
| 5.2.10 / 5.3.5 | Cord anchorage on adjustable luminaire | - Cord anchorage - Adjustable - Cable length |
087.03.OSM |
| 5.2.10 / 5.3.5 | Recessed luminaire delivered with separate control gear | - Complete cord anchorage - Sub clause 5.3.5 - Separate control gear |
088.03.OSM |
| 5.2.10.2 / 5.2.10.3 | Cord anchorage with type Y or Z attachment on Printed Circuit Board | -
Cord anchorage - Soldered connection - Type Y or Z attachment |
089.03.OSM |
| 5.3 | ptfe basic insulated cable | - 0.6mm - PVC and rubber - High Voltage Test |
092.03.LIP |
| 5.2.16 | couplers to be used | - Examples - IEC 60320 - Configurations |
091.03.LIP |
| 5.2.16 | Connectors / screwless terminals | -
Clause 4.11.6 - Appliance inlets - Connectors |
169.03.OSM |
| 5.3 | ptfe basic insulated cable | - 0.6mm - PVC and rubber - High Voltage Test |
092.03.LIP |
| 5.3 | internal wiring for some lamp circuits | - Internal wiring - Insulation resistance - Component |
093.03.LIP |
| 5.3.1 | Through wiring in the luminaires | - Luminaire manufacturer - Skilled persons - Cable/wiring |
094.03.OSM |
| 5.3.3 | Use of additional sleeves | - Construction - Sleeve - Bushings |
095.03.OSM |
| 7.2 | Locking on earthing connection |
- Construction - During mounting - Spacers |
097.03.OSM 097.03.OSM.Figure |
| 7.2.1 | Earthing in luminaire system | - Metal body - Each luminaire - Fixed installation |
098.03.OSM |
| 7.2.1 | Relamping operation | - Breakage - Insulation fault - lamp |
099.03.LIP |
| 7.2.1 | Provisions for earthing | -
Screws connection - Installation - Cleaning |
100.03.OSM |
| 7.2.1 | Electrical connections | - Mechanical stress - Terminal block - Earth connection |
263.03.OSM |
| 7.2.4 | Reliability of the earthing circuit | - Drawing - Way of earthing - Snap-in pins |
101.03.OSM 101.03.OSM.Figure |
| 8 | IP protection of recessed parts | -
Paragraph 8 - IP classifications - Item 12.3 |
147.03.LIP |
| 8 | Standard test finger | - Cross-section area - External connection - Lampholder terminals |
102.03.OSM |
| 8 | Built in components accessibility |
- IP 1X test probe - IEC 60598-1 - Built in components |
103.03.OSM |
| 8.2.1 | Luminaires with LEDs | -
Sub clause 8.2.1 - Lamp compartment - Two lines of defence |
251.03.OSM |
| 8.2.3 | Class II luminaire
with metal reflector |
- Distance - Metal reflector - Lamp replacement |
104.03.OSM |
| 8.2.3 | Metal fixing devices
for components |
- Live parts - Reinforced insulation - Fixing device |
105.03.OSM |
| 8.2.3- | Class I / class II luminaires protection against electric shock | -
D.S. N° 103/03 - Basic insulation - Standard test finger |
266.03.OSM 266.03.OSM.figures |
| 8.2.5 | Class II luminaires
for discharge lamps |
- Constructions - Common sense - LUMEX |
106.03.OSM 106.03.OSM.Figures |
| 8.2.6 | Parts removable by hand | - Force - Common sense - By hand |
107.03.OSM |
| 8.2.7 | Residual voltage | - One luminaire - System - Requirement |
108.03.LIP |
| 9 | IP 65 luminaire | - All parts - Instructions - Gasket |
109.03.OSM |
| 9 | IP 20 luminaire | - Instruction leaflet - Indoor/outdoor - Glands |
110.03.OSM |
| 9 | IP degree | -
IP X3 / X4 - IP X5 / X6 - Procedure |
111.03.OSM |
| 9 / 9.2 | IP X3 and IP X4 tests | -
Ceiling - IP X1 / X2 - More than 10 mm |
112.03.OSM |
| 9.2 | Torque for fixing
screws of covers |
- Instructions - Manufacturer - Table 4.1 |
113.03.OSM |
| 9.2f | Entry of test probes for IP 3X and 4X | -
IEC 60529 - Enclosure - Drain holes |
114.03.OSM 114.03.OSM.Figure1 114.03.OSM.Figure2 114.03.OSM.Figure3 114.03.OSM.Figure4 |
| 9.2 | IP ratings | - Mounting board - 10 mm overhang - IP X3 / X4 |
255.03.LIP |
| 9.2 | Ingress protection / SELV | - Water ingress - SELV parts - Fire risk |
268.03.OSM |
| 10 | Dielectric strength test on bushing | - Class I - II - Bushings - Double insulated cable |
115.03.OSM 115.03.OSM.Figure |
| 10.3 | Network described
in IEC 60990 |
- IEC 60990 - IEC 60598-1 - Measuring network |
116.03.OSM |
| 11 | Distances inside a lamp | - Heating tests - Creepage distances - Components |
117.03.OSM |
| 11 Annex M | Measurements of creepage distances and clearances | -
Maintenance - Live parts - Capacitor case |
118.03.OSM |
| 11.2 | Creepage distances and clearance | -
Annex "M" - Class I, II, III - SELV parts |
119.03.OSM |
| 11.2.1 | Creepage distances and clearances at a supply terminal | -
Lampholders - § 11.2.1 - Supply terminal |
121.03.OSM |
| 11.2.1 | Creepage distances and clearances at a supply terminalPendant luminaire with a "ceiling cone" | -
Mounting surface - Supply wires - Ceiling Cone |
120/03.m |
| 12 | Heating tests for tungsten halogen lamps |
- Highest temperature - Warning notice - Luminaire |
122.03.OSM |
| 12 | Endurance and thermal tests |
- Clause 12 - IR - Time limited controls |
124.03.OSM |
| 12 | endurance
and thermal> tests on appliances for purifying water using an UV lamp |
- Thermal tests - Abnormal conditions - Temperature of water flowing |
544 |
| 12.1 | Temperature
limits of the external parts (metal) of a fixed luminaire |
-
Metal part - 70°C - Fixed luminaire |
280.03.OSM 280.03.OSM.figure |
| 12.2 | Polypropylene used for lampholders | -
Safety - Lampholders - Table 12.2 |
168.03.LIP |
| 12.3 | Interpretation regarding "mounting surface" / "illuminatedsurface" | - Mounting surface - Illuminated surface - Abnormal operation |
125.03.LIP |
| 12.3.1 | Temperature decreasing during endurance test |
- Endurance test - Temperature - Below 25°C |
126.03.OSM |
| 12.4 | Luminaires recessed in the floor | -
Spot light - Halogen lamps - Parts intended to be touched |
127.03.OSM |
| 12.4 | Clarification of
some luminaire parts |
- Handles, knobs - Hand lamps - § 3.3 -IEC 60598-1 |
128.03.OSM |
| 12.4 | Temperature measurement on replaceable glow starting device |
- Starter - IS 18 - Enec approval |
129.03.OSM |
| 12.4.1 | Temperature limit
on terminal block |
- Terminal block - T marking - Clauses 13-14-15 |
130.03.OSM |
| 12.4.2 | Sleeve for earthing supply cable | - Supply cable - Sleeve - Earthing conductor |
131.03.OSM |
| 12.4.2 | Bridging test | -
Normal operation - Bridging test - Tables 12.1 - 12.2 |
184.03.OSM |
| 12.5.1 | Abnormal operation condition |
- IP 00 transformer - IEC 61558-1 - Short-circuit test |
132.03.OSM |
| 12.5.1.4) | Luminaire inoperative after the test |
- Clauses 0.3-12.5) - SELV - Inoperative luminaire |
133.03.OSM |
| 12.5.1a)4) | requirements for convertors> | -
transformers> - Convertors - Requirements |
253.03.LIP |
| 12.6 | "laminated filter coil" | -
§ 12.6> - Laminated filter coil - Small wound devices |
258.03.LIP |
| 12.7 | Temperature extrapolated value |
- The graph - Fixation points - Ball pressure test |
135.03.OSM |
| 12.7.1 | fault condition test | - Normal Operation - Mounting Screws - Sub-Clause 12.6 |
136.03.LIP |
| 12.7.1 | Luminaires in thermoplastic material (fixing points) | -
Ballast - Constructive measures - § 4.15 a) / § 12.7.1 |
248.03.OSM 248.03.OSM.figure1 248.03.OSM.figure2 |
| 13.2.1 | Ball pressure test on soft thermoplastic | -
Ball pressure test - Thermoplastic materials - Reinforced insulation |
137.03.OSM |
| 13.2.1 | Temperature for ball pressure test | -
temperature - hottest point - inner surface |
294.CTL-ETF5 |
| 13.3.1 | Needle flame test
/ glow wire test |
- Needle flame - Glow wire (650°C) - Burning drops |
138.03.OSM |
| annex a | metallic paint | - § 6.1 - IEC 60238 - Metallic paint |
139.03.OSM |
| annex a | push-on lampholders | - Push-on
Lampholder - New Lamps - Live Parts |
211.03.OSM |
| annex c | metallic paint | - § 6.1 - IEC 60238 - Metallic paint |
140.03.LIP |
| annex d | Size of the test
box (min. installation dimensions) |
- Instructions - Annex D - Requirement |
142.03.LIP |
| annex d | insulating material used around the test recess | -
thermal conductivity - Tolerance - 0.04 W/mK |
143.03.OSM |
| Annex D | Test recesses in a luminaire with separate parts | -
Manufacturer instructions - Separating distances - Spacers | 287/04 |
| IEC 60598-1/2003 VI Ed. | |||
| Clause | Subject | Keywords | Sheet |
| 2 | Marking on small luminaires | - Marking - small luminaires - Supply cord |
282.04.OSM |
| 2.6 | "IP X8" Marking | - Marking - Table J.2 - IP X8 |
283.04.OSM |
| 8.2.1 | live metal parts projected from edison screw caps | - Protection against
electric shock - Live metal parts - Standard test finger |
284.04.OSM |
| 8.2.1 | G10q connector's construction | - G10q lampholder - Protection against electric shock - Connector's construction |
PDSH.12.04.OSM |
| 11 | metal screw glands | -
Metal glands - Class II - Clearance and creepage |
285/04 |
| 11.2 | Creepage and clearances between a metal reflector and the cap of a fluorescent lamp | - Basic Insulation - Metallic lamp cap - Metal reflector - Class II Luminaires |
281.04.LIP 281.04.LIP.figure |
| IEC 60598-2-1/1979 and A1/1987 | |||
| Clause | Subject | Keywords | Sheet |
| General | Applicable standard | - Standard - IEC 60598-2-5 - IEC 60598-2-1 |
246.03.OSM |
| IEC 60598-2-2/1996 and A1/1997 | |||
| Clause | Subject | Keywords | Sheet |
| 2.11 | Consideration relevant built-in components | -
Built-in components - Outside of the luminaire - 34D/Lumex(Sec)590 |
148.03.OSM 148.03.OSM.figures |
| 2.11 | IP protection of recessed parts | -
Paragraph 8 - IP classifications - Item 12.3 |
147.03.LIP |
| 2.11 | Luminaire with R7s/RX7s lamp cap | -
Lampholder - Connecting device - Recessed luminaire |
149.03.OSM |
| 2.11 | Built in components accessibility |
- IP 1X test probe - IEC 60598-1 - Built in components |
103.03.OSM |
| Annex D | Test recesses in a luminaire with separate parts | -
Manufacturer instructions - Separating distances - Spacers | 287/04 |
| IEC 60598-2-3/1997 and A2/2002 | |||
| Clause | Subject | Keywords | Sheet |
| 3.6.3.1 | Wind force test | -
Weight - Wind force test - Top of the mast |
157.03.LIP |
| IEC 60598-2-3/2003 | |||
| Clause | Subject | Keywords | Sheet |
| 3.6.3 | Wind force test | -
Complete luminaire - Two fixing devices - Risk of falling |
150.03.OSM |
| 3.6.3.1 | Wind force test | -
Weight - Wind force test - Top of the mast |
157.03.LIP |
| IEC 60598-2-4/1997 | |||
| Clause | Subject | Keywords | Sheet |
| Definitions | Portable luminaires Garden luminaires Lighting chains | - Marking - Type reference - Mounting instruction |
ETF5-OSM/LUM-04-2004 |
| General | Applicable standards | -
IEC 60335-1 - Warning label - Sealed tube - 3D characters |
272.03.OSM 272.03.OSM.Figures |
| 10.3 | Portable/Child appealing luminaire | -
Portable - Child-appealing - Appliance |
161.03.OSM 161.03.OSM.Figures |
| 4.12.4/4.6 | mechanical connections lampholder between different parts of luminaire | - electrical connections strain cord anchorage> | 523.OSM/CTL-ETF5 |
| IEC 60598-2-5/1998 | |||
| Clause | Subject | Keywords | Sheet |
| General | Applicable standard | - Standard - IEC 60598-2-5 - IEC 60598-2-1 |
246.03.OSM |
| IEC 60598-2-6/1994 and A1/1996 | |||
| Clause | Subject | Keywords | Sheet |
| General | Applicability of IEC 598-2-6 | -
IEC 598-2-6 - Transformer - Converter |
158.03.OSM |
| General | Transformers to be used | -
Basic insulation - SELV transformers - Supplementary insulation |
159.03.LIP |
| 12.5.1a)4) | requirements for convertors | -
transformers - Convertors - Requirements |
253.03.LIP |
| IEC 60598-2-7/1982 + A1/1987 + A2/1994 | |||
| Clause | Subject | Keywords | Sheet |
| Definitions | Portable luminaires Garden luminaires Lighting chains | - Marking - Type reference - Mounting instruction |
ETF5-OSM/LUM-04-2004 |
| IEC 60598-2-8 Ed.1 | |||
| Clause | Subject | Keywords | Sheet |
| 8.6.2 | Handlamps for tungsten filament lamps |
- protecting device - screwed fixing |
272.CTL-ETF5 |
| 8.6.6.1 | Mechanical strength for handlamps |
- Suspension hook - Grid or guard (translucent cover) - 250 N pull |
435.CTL-ETF5 |
| IEC 60598-2-10/1987 and A1/1990 and A2/1995 | |||
| Clause | Subject | Keywords | Sheet |
| 10.3 | Portable/Child appealing luminaire | -
Portable - Child-appealing - Appliance |
161.03.OSM 161.03.OSM.figures |
| IEC 60598-2-10/2003 | |||
| Clause | Subject | Keywords | Sheet |
| General | Examples of luminaires | - Doll - Snowman - Lamps with angel and bear |
270.03.OSM 270.03.OSM.figures |
| IEC 60598-2-17/1984 and A1/1987 and A2/1990 | |||
| Clause | Subject | Keywords | Sheet |
| 17.6.4 | Devices against loosening | -
Flat washer - Spring washer - Loosening |
162.03.LIP |
| 17.6.5 | Term "properly inserted" | -
Mechanical means - Weight - Section 17 |
163.03.LIP |
| IEC 60598-2-20 Ed.2 | |||
| Clause | Subject | Keywords | Sheet |
| 20.5.1d | Marking of lighting chains intended for interconnection | - marking - lighting chains - interconnection |
254.CTL-ETF5 |
| 20.12.3 | Filament lamps bridging | - bridging device - filament lamp |
271.CTL-ETF5 |
| IEC 60598-2-20/1996 and A1/1998 and A2/2002 | |||
| Clause | Subject | Keywords | Sheet |
| Definitions | Portable luminaires Garden luminaires Lighting chains | - Marking - Type reference - Mounting instruction |
ETF5-OSM/LUM-04-2004 |
| Definitions | Lighting chains | -
IEC 60598-2-20 - Frame - Part 2-4 |
152.03.OSM |
| General | Lighting chains with portable socket outlet | -
Socket outlet - Configuration - Total current |
164.03.OSM |
| General | Lighting device for B22 lighting chains | - Lighting device - Lighting chain - IEC 60598-2-20 - IEC 60968 - IEC 60061 |
165.03.OSM 165.03.OSM.figure |
| General | Lighting chains for outdoor use | - IEC
61558-1 - Transformers - Outdoor use |
166.03.OSM |
| General | Sealed lighting chain fixed on portable decoration | - Christmas lighting device - IEC 60598-2-4 - IEC 60598-2-20 |
167.03.OSM |
| General | Applicable standards | -
IEC 60335-1 - Warning label - Sealed tube - 3D characters |
272.03.OSM 272.03.OSM.Figures |
| 5.2.16 | Connectors / screwless terminals | -
Clause 4.11.6 - Appliance inlets - Connectors |
169.03.OSM |
| 12.2 | Polypropylene used for lampholders | -
Safety - Lampholders - Table 12.2 |
168.03.LIP |
| 20.2 | Tests on integrated B22 lampholders of IP 44 lighting chains | - Integrated lampholder - IEC 61184 - Requirements |
170.03.OSM |
| 20.3.3/ 20.6.14/ 20.10.1 | Sealed lighting chains (rope lights) of PVC for outdoor use | -
Rope lights - Cylinder test - Connecting cable |
171.03.OSM |
| 20.4/ 20.4.2 |
Lighting chain, (indoor or outdoor use) | -
Certification Bodies - IP 44 - Plug transformer |
172.03.OSM |
| 20.5.1 | Marking on lighting chains | -
Warnings - Packing - Clause 20.5.1 b), c), d), e) |
173.03.OSM |
| 20.5.1 | Lighting chains | - Interconnection - Divisible plug - Warning |
174.03.OSM |
| 20.6 | Connections on lighting chains | -
Connection - Sleeving - Two separate layers |
175.03.OSM |
| 20.6.1 | E14 lampholder used in lighting chains | - E14 lampholder - Lighting chain - IEC 60238 |
288/04 |
| 20.6.4 | Construction | -
Connections - Rope light - Current carrying parts |
271.03.OSM |
| 20.6.5 | Lighting chains with lamps and gaskets not fitted | -
Gaskets - Lamps - Mounting instructions |
176.03.OSM |
| 20.6.5 | Lighting chain with more than one loop | -
Plug - Three wires - Three loops |
177.03.OSM |
| 20.6.13/ 20.11.3 | Test conditions for lampholders | -
Operating condition - Push in lamp - 20.11.3 / 20.6.13 |
178.03.OSM |
| 20.6.14 | Mechanical tests of sealed lighting chains | -
Sealed lighting chain Mechanical tests - Temperature |
179.03.OSM |
| 20.6.15 | Mechanical testsn the glass bulb of class III lighting chains | - Class III - Mechanical tests - Lamp blub |
PDSH.11.04.OSM |
| 20.10.2 | Conductors and contacts of lampholders | -
Cord anchorage - Mechanism - Both tests |
180.03.LIP |
| 20.10.2 | Lighting chains | - Pulling Test - Conductors - Class II / III |
181.03.OSM |
| 20.12 | Temperature limits of the bulb of lighting candles | -
Temperature - Bulb - Black board |
182.03.OSM |
| 20.12.3 | Filament lamps bridging | -
Complete set - One by one - Bridging device |
183.03.OSM |
| 20.12.3 | Bridging test | -
Normal operation - Bridging test - Tables 12.1 - 12.2 |
184.03.OSM |
| 20.14 | High voltage test | -
Outdoor use - Indoor use - Metal foil |
185.03.O SM |
| 20.12 | Temperature limits of the bulb of lighting candles | -
Temperature - Bulb - Black board |
182.03.OSM |
| IEC 60598-2-20, Consolidated Edition 2.2 (2002) | |||
| Clause | Subject | Keywords | Sheet |
| 20.10.1 | Cross sectional area of the conductors | -
IS 03 - Indoor / Outdoor application - Cross-sectional areas - Plug / Sealed chain |
257.03.LIP |
| IEC 60598-2-22 Ed.3 | |||
| Clause | Subject | Keywords | Sheet |
| 22.6.3 | Fuses in the emergency lighting luminaires | - fuse wire - failure |
266.CTL-ETF5 |
| IEC 60598-2-22/1997 and A1/2002 | |||
| Clause | Subject | Keywords | Sheet |
| General | Alternative batteries | -
Battery - Every type - Electrical characteristics |
187.03.O SM |
| General Annex A |
Batteries | - Batteries - Elevated temperatures - IEC 60285 |
290/04 |
| 22.3 | Emergency luminaire in two separate parts | -
Installer - PVC or Rubber - Instruction |
188.03.O SM |
| 22.5.2 | Marking | -
Rest mode - Capital "B" - Emergency luminaire |
189.03.OSM |
| 22.5.6 | Marking of duration of operation | -
Codes - Duration of operation - Type reference |
190.03.OSM |
| 22.5.13 | Flux measurement tolerances | - Follow up tests - 10% difference - Type tests |
191.03.O SM |
| 22.6 | Self-contained emergency luminaire with several filament lamps | -
Indicator - Each lamp - Filament lamps |
192.03.OSM |
| 22.6.2 | High frequency data sheets for lamps | -
Data sheets - Lamps - IEC publication |
193.03.OSM |
| 22.6.3 | Fuses in the emergency lighting luminaires | -
Proper fuse - Fuse wire - Print conductor |
194.03.O SM |
| 22.6.7 | Indicator to be incorporated | -
Indicator - Luminaire - Within 1 metre |
195.03.LIP |
| 22.6.8 | Batteries characteristics | -
Manufacturer - Ni-Mh batteries - Life time / temperature |
196.03.O SM |
| 22.12.7 | Lamps for photometric tests | -
Photometric tests - Endurance test - Lamp(s) |
197.03.O SM |
| 22.15 | Enclosure of an emergency luminaire | -
Electric parts - Enclosure - Glow-wire test at 850°C |
198.03.O SM |
| 22.16.1 | Rated lumen output for emergency safety sign using LED lamp array as light source | - Lumen output - LED lamp - Reference lamps |
289/04 |
| 22.16.5a | Measurement of the colour of self illuminated emergency lighting luminaires with exit legends/pictograms | -
Illuminated signs - OSM/LUM Enquiry - 06/2001 - Internal light source |
199.03.LIP |
22.17.3 |
Ballast Lumen Factor (BLF) and flux output measurement after 500 ON-OFF changeover operations | -
ballast lumen factor (blf) - Flux measurement - Changeover operations |
279.03.OSM |
| Annex A/ A.4.2 | Battery compartment temperature | -
LUMEX ELP - 50°C - Continuous overcharge period |
200.03.OSM-LIP |
| A.4.2a) A.5.2a) |
Temperature measurement on the battery | -
Thermocouple - Battery body - Hottest part |
201.03.OSM |
| A.4 - A.7 | Discharge
current for NiCd batteries |
-
Declaration - Manufacturer - Batteries - Discharge current |
273.03.OSM |
| IEC 60838-1 Ed.1 | |||
| Clause | Subject | Keywords | Sheet |
| - | Edition of the gauge
sheet, when testing lampholder |
- gauge - lampholder |
258.CTL-ETF5 |
| IEC 60838-1/1997 and A1/1999 and A2/2002 | |||
| Clause | Subject | Keywords | Sheet |
| General | "Special" lampholder | -
Special lampholder - Enec mark - Pillar terminal block |
213.03.OSM |
| IEC 60884-1/1994 | |||
| Clause | Subject | Keywords | Sheet |
| General | Issue of a CCA-STR for a plug in surge protector within CCA Agreement | - Surge protector - Plug - Socket-outlet |
OSM/IN 204 |
| IEC 60921/2003 A2/1994 | |||
| Clause | Subject | Keywords | Sheet |
| General | Samples selection (family products) | -
Samples selection - Family products - Ballasts |
215.03.OSM |
| IEC 60923/1995 | |||
| Clause | Subject | Keywords | Sheet |
| General | Samples selection (family products) | -
Samples selection - Family products - Ballasts |
215.03.OSM |
| General | Ballast with additional terminals (to reduce the current) | -
Rated conditions - Windings - Safety requirements |
218.03.OSM |
| IEC 60927/1997 and A1/1999 | |||
| Clause | Subject | Keywords | Sheet |
| 12.1-12.2 | Endurance test for built-in ignitors in the rectifying test circuit | -
Test quantity - Additional ignitors - 30 days |
225.03.OSM |
| IEC 60929/1990 and A1/1994 and A2/1996 | |||
| Clause | Subject | Keywords | Sheet |
| 7 | Voltage across lamp during pre-heating time | - Residual d.c. voltage - Measurement - Pre-heating time |
230.03.OSM 230.03.OSM.figures |
| 7.2 | Preheat starting mode | -
Data sheets - Preheat starting mode - IEC 60081 / 60901 |
231.03.OSM |
| 11-A.5 15-A.5 | Application of EN 61547 | -
IEC 60929 / 61047 - EN 61547 - Requirements |
237.03.OSM |
| Annex
A.4 Annex A.4.1 |
Open circuit voltage measurements | -
Instructions - Lamp manufacturer - Preheating |
232.03.OSM |
| IEC 60968/1999 | |||
| Clause | Subject | Keywords | Sheet |
| - | Measurement of circuit power factor and supply current | - True power factor - Supply current - High frequency components |
PDS ETF5-OSM/LUM- 06-2004 |
| IEC 60969/1990 and A1/1994 and A2/1996 | |||
| Clause | Subject | Keywords | Sheet |
| 8.4 | Lamp current limit for HF Lamps with no data for Relevant HF reference Ballast in data sheets IEC 60081 / 60901 | -
Lamp current - Lamp data sheet - Reference ballast - Calibration current |
274.03.OSM |
| IEC 60969/2000 | |||
| Clause | Subject | Keywords | Sheet |
| - | Measurement of circuit power factor and supply current | - True power factor - Supply current - High frequency components |
PDS ETF5-OSM/LUM- 06-2004 |
| EN 60998-2-1:2004 | |||
| Clause | Subject | Keywords | Sheet |
| General | Applicable standards to connecting devices for flexible cords |
- connecting devices - flexible cords |
OSM/IN 249 |
| IEC 60998-2-2:2004 | |||
| Clause | Subject | Keywords | Sheet |
| 10.103 | Accepting of smaller range of cross-sectional areas | - Terminal - Connecting capacity -cross-sectional areas |
OSM-IN 228 |
| IEC 61047/1991 and A1/1996 and A2/2001 | |||
| Clause | Subject | Keywords | Sheet |
| General | Samples selection, (family products) | -
Step-down convertors - Samples selection - IEC 1046 / 1047 |
233.03.OSM |
| 7 - 8 - 9 | Cables for convertors | -
20 cm - Length specified - Manufacturer |
236.03.OSM |
| 11-A.5 15-A.5 | Application of EN 61547 | -
IEC 60929 / 61047 - EN 61547 - Requirements |
237.03.OSM |
| IEC 61048/1991 + Ec/1992 and A1/1995 and A2/1999 | |||
| Clause | Subject | Keywords | Sheet |
| 4 | Sampling plan | -
Capacitance - Self-healing capacitor - 50 capacitors |
276.03.OSM |
| 17 | Use of the previous tested sample | - Test time - Destruction test - Proposal |
238.03.OSM |
| IEC 61049/1991 and Ec/1992 | |||
| Clause | Subject | Keywords | Sheet |
| 3 | Sampling plan | -
Capacitance - Self-healing capacitor - 50 capacitors |
276.03.OSM |
| 8 | Measurement of tangent of loss angle on capacitors | -
Discharge resistor - Capacitor - Tangent of loss angle |
239.03.OSM |
| IEC 61184/1997 | |||
| Clause | Subject | Keywords | Sheet |
| figure 17 | protection against ingress of water | - drop of liquid holes equipment ingress water | 398.CTL-ETF5 |
| - | Edition of the gauge sheet, when testing lampholder | - gauge - lampholder |
258.CTL-ETF5 |
| IEC 61347-1/2000 I Ed. | |||
| Clause | Subject | Keywords | Sheet |
| General | Applicable Standards | -
components - Temperatures - Heating Test |
219.03.OSM |
| General | Samples selection (family products) | -
Samples selection - Electronic ballast - Ignitors |
221.03.OSM |
| Annex A | Test to establish whether a conductive part is a live part which may cause an electric shock | - Earth - Accessible part - A2 test |
240.03.OSM |
| annex b | annex b | -
Discharge lamps - Thermal protector - IEC 60730-2-9 |
220.03.OSM |
| 7.1 | Marking according to the safety requirements | -
Safety requirements - Performance criteria - Performance marking |
241.03.OSM |
| Annex 1 | ballast with double or reinforced insulation | - Safety requirements - Two layers - Distances |
250.03.OSM |
| 14.1 | short circuit across creepage distances and clearances | - PCB - Creepage distance and clearance |
277.03.OSM |
| IEC 61347-2-1/2000 I Ed. | |||
| Clause | Subject | Keywords | Sheet |
| General | Samples selection (family products) | -
Samples selection - Electronic ballast - Ignitors |
221.03.OSM |
| 6 | Ignitor marked "- 30°C" | -
-30°C - Marking - Ignitor |
224.03.OSM |
| 7.1 | Marking according to the safety requirements | -
Safety requirements - Performance criteria - Performance marking |
241.03.OSM |
| IEC 61347-2-2/2000 | |||
| Clause | Subject | Keywords | Sheet |
| General | Samples selection, (family products) | -
Step-down convertors - Samples selection - IEC 1046 / 1047 |
233.03.OSM |
| appendix b | Heating Test for convertors | -
tc value - Independent convertors - Marking |
235.03.OSM |
| 7.1 | Marking according to the safety requirements | -
Safety requirements - Performance criteria - Performance marking |
241.03.OSM |
| 8 | Protection against accidental contact with live parts |
-
one capacitor - Y1Two times Y2 |
278.03.OSM |
| 14 | Temperature on the capacitors | -
Heating Test - Capacitors - T marking |
234.03.OSM |
| IEC 61347-2-3/2000 I Ed. | |||
| Clause | Subject | Keywords | Sheet |
| general | Uncased ballasts, convertors | -
Mandatory markings - EN 61347-2-3 - Label/ ballast |
221.03.OSM |
| general | Uncased ballasts, convertors | -
Mandatory markings - EN 61347-2-3 - Label/ ballast |
226.03.OSM |
| 7.1 | Marking according to the safety requirements | -
Safety requirements - Performance criteria - Performance marking |
241.03.OSM |
| 7.2 | Working voltage measurement | -
Working voltage - Terminals - Earth |
227.03.OSM |
| 7.2 | Information to be provided | -
Rated voltage - 250 V - Information |
228.03.OSM |
| appendix b | Thermally protected electronic components | -
PTC - Devices - Supply Circuit |
229.03.OSM |
| IEC 61347-2-7/2000 I Ed. | |||
| Clause | Subject | Keywords | Sheet |
| General | Samples selection (family products) | -
Samples selection - Electronic ballast - Ignitors |
221.03.OSM |
| 7.1 | Marking according to the safety requirements | -
Safety requirements - Performance criteria - Performance marking |
241.03.OSM |
| 15.3 | Lamp starting test following 3x200 lamp switching | - Within 1 second - Applied tolerance - Correct pre-heating |
242.03.OSM |
| 19 | Lamp operating current waveform | - RMS value - Thermal result - All the periods |
243.03.OSM |
| section 6 §33 | Measurement of the ratio of the luminaire flux | -
Measurement - Design voltage - COMEX / LUMEX |
222.03.OSM |
| section 6 §38 | Battery recharging test | -
Battery - Recharging test - Conditioning cabinet |
223.03.OSM |
| 20 | Ballast Lumen Factor (BLF) and flux output measurement after 500 ON-OFF changeover operations | -
ballast lumen factor (blf) - Flux measurement - Changeover operations |
279.03.OSM |
| IEC 61347-2-8/2000 | |||
| Clause | Subject | Keywords | Sheet |
| General | Tolerance on delta T value | -
Tolerance - Delta T value - Temperatures |
216.03.OSM |
| 6 | Serial compensation for ballast | -
Tolerances - Capacitor - Ballast |
217.03.OSM |
| 7.1 | Marking according to the safety requirements | -
Safety requirements - Performance criteria - Performance marking |
241.03.OSM |
| IEC 61347-2-9/2000 | |||
| Clause | Subject | Keywords | Sheet |
| General | Tolerance on delta T value | -
Tolerance - Delta T value - Temperatures |
216.03.OSM |
| General | Samples selection (family products) | -
Samples selection - Family products - Ballasts |
215.03.OSM |
| General | Ballast with additional terminals (to reduce the current) | -
Rated conditions - Windings - Safety requirements |
218.03.OSM |
| General | Applicable Standards | -
components - Temperatures - Heating Test |
219.03.OSM |
| 6 | Serial compensation for ballast | -
Tolerances - Capacitor - Ballast |
217.03.OSM |
| 7.1 | Marking according to the safety requirements | -
Safety requirements - Performance criteria - Performance marking |
241.03.OSM |
| annex b | annex b | -
Discharge lamps - Thermal protector - IEC 60730-2-9 |
220.03.OSM |
| Annex 1 | ballast
with double or reinforced insulation |
- Safety requirements - Two layers - Distances |
250.03.OSM |
| IEC 61558-1/1997 and A1/1998 | |||
| Clause | Subject | Keywords | Sheet |
| 14.2 | temperature of supports for transformers ip 00 | - temparature of supports - IP 00 - TRF |
291/04 |
| 15.3.2 | short circuit and overload protection | - fuse current overloading test overload | 244.03.OSM |
| 20.5 | thermal cut-outs | - ptc / resistor bi-metal contacts iec 60730 | 245.03.OSM |
| 3.1.9.1 3.1.11 15.3, 15.5, 27.3 |
Heat and fire protection | -
Non-inherently short circuit - Proof transformer - Fail-safe transformer |
522.OSM/CTL-ETF5 |
| HA EN GENERAL | |||
| Clause | Subject | Keywords | Sheet |
| Procedure | -
Components - Certificates |
0040.OSM-HA | |
| Procedure | -
Country of origin - CCA-NTR |
0184.OSM-HA | |
| Procedure | - Test report form | 0185.OSM-HA | |
| Procedure | - CCA-NTR for components | 0187.OSM-HA | |
| 7.10 | Procedure | - series of models | 0007.OSM-HA |
| IN EN GENERAL |
|||
| Clause | Subject | Keywords | Sheet |
| - | Locking device for rivets serving as electrical as well as mechanical connections | Locking device | 001.OSM-IN |
| General | Instrument accuracy limits to be considered in CCA testing. | Instrument accuracy limits | 004.OSM-IN |
| EN 50075:1991 | |||
| Clause | Subject | Keywords | Sheet |
| General | Coil incorporated in 2.5 A Europlugs | Coil | OSM/IN 202 |
| 17 | Glow-wire test | Glow-wire test | 020.OSM-IN |
| EN 50086-2-4:1994 | |||
| Clause | Subject | Keywords | Sheet |
| General | Testing programme for a range of conduit sizes | Testing programme | 023b.OSM-IN |
| EN 50144-1:1998 | |||
| Clause | Subject | Keywords | Sheet |
| 25.1 | Earthing | -
Universal type motors - Motor shaft - Class II construction |
0288.OSM-HA |
| EN 50366:2003 | |||
| Clause | Subject | Keywords | Sheet |
| General | EMF | - guide for EMF | OSM/HA 395 |
| EN 60065:1998 | |||
| Clause | Subject | Keywords | Sheet |
| Please click here in order to access sheets forEN 60065:1998, EN 60065:1998 & 60065:2002, EN 60065:2002 & EN 60065:2002 + A1 | |||
| General | Use of pre-certified components | 98_8OSM-EE | |
| 5 | Marking of Components | -Marking - Components |
00_8OSM-EE |
| 7.2, Note 2 | Softening temperature | -
Softening Temperature - Vicat-Test |
99_7OSM-EE |
| 14 | Surge suppressors | - Surge suppressors | 00_13OSM-EE |
| 14.2.5 | Short circuit of X-capacitors | -
X-Capacitors - Short circuit |
00_3OSM-EE |
| 14.3.2 | Inductors and windings | -
Flammability - Burning Drops |
99_8OSM-EE |
| 14.4 | High voltage components and assemblies | -
Flammability - Burning Drops |
99_9OSM-EE |
| 14.6.1 | Mains on/off relays | -
Mains switches - mains relays |
01_1OSM-EE |
| 14.6.2 | Mains on/off switch | -
Mains switches - mains relays - Manually Operated Mechanical Switch |
00_2OSM-EE |
| EN 60309-2:1999 | |||
| Clause | Subject | Keywords | Sheet |
| 12.3 | Measurement of height of retaining means for IP44 socket-outlets and connectors | - Retaining means | OSM/IN 201 |
| EN 60320-1:2001 | |||
| Clause | Subject | Keywords | Sheet |
| 13.1 | Certification of non-rewirable connector intended for use as a part of a cord set or an interconnection cord set | - Non-rewirable connector - Cord set - Interconnection cord set |
OSM-IN 220 |
| 15.3 | Test voltage for appliance couplers | - Test voltage | OSM-IN 221 |
| 16.2 | Withdrawal force test | - Withdrawal force test | OSM-IN 222 |
| EN 60335-1:1988 | |||
| Clause | Subject | Keywords | Sheet |
| 19 | Abnormal operation | -
thermostat and thermal cut out - one temperature sensing device |
0030.OSM-HA |
| 22.22 | Earthing | -
Snap-on connectors - Earth continuity |
0058.OSM-HA |
| 25.13 | Internal conductors | - Accessible internal conductors | 0054.OSM-HA |
| 25.13 | Connector | - Special connector | 0165.OSM-HA |
| 27.2 | Earthing | -
Snap-on connectors - Earth continuity |
0058.OSM-HA |
| 27.2 | Earthing | -
Pillar type terminals - Pressure plate |
0059.OSM-HA |
| 27.4 | Earthing | -
Pillar type terminals - Pressure plate |
0060.OSM-HA |
| 29.1 | Creepage/clearance | - Resonance voltage exceeding 440V | 0063.OSM-HA |
| EN 60335-1:1994 | |||
| Clause | Subject | Keywords | Sheet |
| 2 | Current-carrying hose | - Current carrying hoses | 0250.OSM-HA |
| 2.7.1 and 2.7.2 | Definitions | - Detachable and non detachable parts | 0214.OSM-HA |
| 7.10 | Marking | - push-push main switch | OSM/HA 09 |
| 7.12 | Marking | - instruction sheet | 0011.OSM-HA |
| 7.14 | Marking | - Adhesive label | 291.OSM-HA |
| 8 | Protection against electric shock | - Paint as insulation | 0015.OSM-HA |
| 8 | Protection against electric shock | -
Enclosure of plastic material - Portable fan heaters |
0192.OSM-HA |
| 8 | Protection against electric shock | - Part of luminaires on the appliances | 0210.OSM-HA |
| 8 and 20 | Interlock Switches | - Interlock switches | 0249.OSM-HA |
| 8.1 | Protection against electric shock | -
test finger - test pin |
0013.OSM-HA |
| 8.1 | Protection against electric shock | - Appliances including luminaires | 292.OSM-HA |
| 8.1.1 and 8.1.2 | protection against electric shock | - Fluorescent lamps behind detachable cover | 0215.OSM-HA |
| 8.2 | Protection against electric shock | -
Basic insulation - - Paint coating |
0231.OSM-HA |
| 11 | Heating | -
Type X attachment - Permanent connection |
0020.OSM-HA |
| 11 | Heating | - Appliance inlets | 0022.OSM-HA |
| 11.8 | Heating | -
other purposes than electrical insulation - table 3 |
0025.OSM-HA |
| 12 | Endurance and thermal tests on appliances for purifying water using an UV lamp | - Thermal tests - Abnormal conditions - Temperature of water flowing |
544 |
| 13.2 | Leakage current | -
3 phase heating element - 1 phase motor |
0027.OSM-HA |
| 15.1.2 | Moisture resistance | -
IPX3 - IPX4 - Ceiling mounted appliances |
0232.OSM-HA |
| 17 | Overload protection | - Transformers | 0238.OSM-HA |
| 19.13 | Abnormal operation | - Thermal cut-outs | 0216.OSM-HA |
| 19.7 | Abnormal operation | -
Miniature fuses - Protection for motors |
0194.OSM-HA |
| 19.7 | Abnormal operation | - Short circuiting motor capacitator | 327.OSM-HA |
| 19.11.2 | Microprocessors | - Faults on microprocessor | 0077.OSM-HA |
| 19.11.2 | Abnormal operation | - electronic control | 328.OSM-HA |
| 20 | Protection against electric shock | -
Enclosure of plastic material - Portable fan heaters |
0192.OSM-HA |
| 22.31 | Construction | - snap-on connection | 0033.OSM-HA |
| 22.31 | Construction | - snap-on connection | 035.OSM-HA |
| 22.40 | Switches | -
Components - Electronic switches |
0051.OSM-HA |
| 22.42 | Protective impedance | -
Protective impedance - Y1 capacitor |
0079.OSM-HA |
| 22.44 | Construction key | - Enclosure - Design and shape |
330.OSM-HA |
| 24 | Fuse-links | -
Components - Fuse- links |
0042.OSM-HA |
| 24 | Procedure | - Components | 0230.OSM-HA |
| 24 | Switches | -Resistive
and inductive load for switches -Annex F of EN 61058-1 |
0316.OSM-HA |
| 24.1 | Timers | -
Components - Timers - Endurance |
0049.OSM-HA |
| 24.1.1 | Transformer | - Transformers | 0217.OSM-HA |
| 24.1.4 | Transformer | -
Transformers with T marking - Ambient temperature |
0234.OSM-HA |
| 24.1.4 | Components | -
Plugs - IPX4 |
0273.OSM-HA |
| 25 | Plug pins | -
Components - Plug pins incorporated in the appliances |
0053.OSM-HA |
| 25.8 | Detachable supply cords | -
Supply cords - Cross sectional area |
0301.OSM-HA |
| 26.1 | Construction | - snap-on connection | 035.OSM-HA |
| 26.11 | Terminals | - stranded conductor | 0304.OSM-HA |
| 27.4 | Earthing | - Rapid clip for main earthing | 0218.OSM-HA |
| 27.4 | Earthing | -
Risk of corrosion - Earthing terminals |
0277.OSM-HA |
| 27.4 | Earthing | -
Risk of corrosion - Earth continuity |
0278.OSM-HA |
| 28.1 | Screws and connections | - Torque test | 0271.OSM-HA |
| 28.3 | Screws and connections | -
Threaded cutting screws - Threaded forming screws |
0274.OSM-HA |
| 28.3 | Screws and connections | -
Taptile screws - Earth continuity |
0279.OSM-HA |
| 29.1 | Creepage/clearance | - Live parts of different polarity | 0219.OSM-HA |
| 29.1 | Creepage/clearance | -
Switches - Terminals |
0235.OSM-HA |
| 29.1 | Creepage/clearance | - Reinforced insulation for working voltages between 250 and 480V | 0293.OSM-HA |
| 29.1 | Creepage/clearance | -
printed circuit - distances on printed conductors |
0305.OSM.HA |
| 29.1 | Creepage/clearance | - Resonance voltages exceeding 440V | OSM/HA 63 |
| 29.2 | Distance | - Insulation between layers thermally bonded together | 0066.OSM-HA |
| 29.2 | Distance | -
Supplementary insulation - Reinforced insulation |
0196.OSM-HA |
| 29.2 | Distance | - Transformers | 0236.OSM-HA |
| 29.2.2 | Distance | -
Thin sheet - Reinforced insulation |
0195.OSM-HA |
| 30 | Heat/fire/tracking | - Internal wiring | 0068.OSM-HA |
| 30 | Heat/fire/tracking | -
Crimp connection - Ball pressure test - Glow wire test |
0280.OSM-HA |
| 30.1 | Heat/fire/tracking | -
External parts - Hottest point |
0070.OSM-HA |
| 30.1 | Heat/fire/tracking | - Ball pressure test | 0072.OSM-HA |
| 30.2 | Heat/fire/tracking | - close proximity | 329.OSM-HA |
| 30.2.2 and 30.2.3 | Heat/fire/tracking | - Material supporting connections | 0237.OSM-HA |
| 30.2.3 | Heat/fire/tracking | -
Bad connection test - Glow wire test |
0308.OSM-HA |
| App. B | Functional earthing | -
Earthing of output winding of SELV transformer - Protective impedance |
0075.OSM-HA |
| Annex P | Duty conditions | -
Normal duty conditions - Carbon dust |
0197.OSM-HA |
| EN 60335-1/2002 | |||
| Clause | Subject | Keywords | Sheet |
| 1 | Scope | - portable foot whirlppool bath (foot spa) | OSM-HA 389 |
| 1 | Scope | - combined appliances - EN 60065 and 60950 |
OSM/HA 324 |
| 2 | Normative references | - TNV circuits - TLC circuits - IEC62151/2000 |
335.OSM-HA |
| 3.1.11 and 3.8.2 | Definitions | - possible unsafe operation - not possible unsafe operation |
OSM/HA 401 |
| 3.3.6, 22.7 and 22.42 | Definitions | - protective impedance - Y1 type capacitors |
OSM/HA 432 |
| 3.8.2 | Definitions | - off position - stand by position |
OSM/HA 402 |
| 3.8.3 | Definitions | - visibly glowing heating elements | OSM/HA 436 |
| 5.8.1 | General conditions for the tests | - Rated frequency - Induction motor - Locked rotor testing |
331.OSM-HA |
| 7.10 | Marking | - push-push main swith | OSM/HA 09 |
| 7.15 | Marking | - class III appliance - selv transformer |
OSM/HA 403 |
| 8 | Protection against electric shock | - application of the test finger | OSM/HA 437 |
| 8.1.5 | Protection against shocks | - installation - fixed appliance |
OSM/HA 420 |
| 8.2 | Protection against electric shock | - Fluorescent lamps behind detachable cover | OSM/HA 215 |
| 8.2 | Protection agains electric shock | - basic insulation - paint coating |
OSM/HA 231 |
| 8 and 20 | Interlosk switches | - interlock switches | OSM/HA 249 |
| 10.1 | Input and curret | - PTC heating element - Representative period |
336.OSM-HA |
| 11 | Heating | - ambient temperature exceeding 25°C | 353.OSM-HA |
| 11 and 19 | Heating | - Purifiying water appliance - U.V. lamp |
332.OSM-HA |
| 11 and 19 | Heating and Abnormal operation | - Insulation class of motor - Classification of the claslation |
421.OSM-HA |
| 7.12 | Marking | - instruction sheet | OSM/HA 11 |
| 15.1.2 | Moisture resistance | - cord reel (automatic) | 354.OSM-HA |
| 15.2 | Moisture resistance | - pouring test - appliances loaded from the top |
OSM/HA 355 |
| 19 | Abnormal operation | -acceptance criteria | 362.OSM-HA |
| 19 | Abnormal operation | - VDR | OSM/HA 396 |
| 19 | Abnormal operation | - thermostat and thermal cut out - one temperature sensing device |
OSM/HA 30 |
| 19 and 29 | Abnormal operation | - motor protector | OSM/HA 398 |
| 19.5 | Abnormal operation | - tubular sheated or embedded heating elements - PVC insulated heating elements |
OSM/HA 404 |
| 19.7 | Abnormal operation | - blocking of moving parts | OSM/HA 438 |
| 19.11 | Abnormal operation | - VDR | OSM-HA 372 |
| 19.11.1/2/3/4 and 20.46 | Abnormal operation | - Protective Electronic Circuit (PEC) - Soft ware classification |
OSM-HA 379 |
| 19.11.3 | Abnormal operation | - PEC's | OSM/HA 430 |
| 19.11.2 | Abnormal operation | - stand by circuits - dangerous malfunction |
OSM/HA 405 |
| 19.13 and 19.11.4 | Abnormal operation |
- hot water and steam emission |
OSM-HA 390 |
| 19.11.4.1 to 19.11.4.8 | Abnormal operation | - electronic switch - stand by position |
OSM/HA 406 |
| 19.11.4.4 | Abnormal operation | - surges | OSM/HA 407 |
| 19.11.4.4 | Abnormal operation | - surges - EMC testing |
OSM/HA 428 |
| 19.13 | Abnormal operation | - supply cord with T marking - table 9 |
OSM/HA 417 |
| 19.14 | Abnormal operation | - contactors - relays |
OSM/HA 422 |
| 20.2 | Mechanical Hazards | - test fingers -accessibility to moving parts |
OSM/HA 416 |
| 22.21 and 22.32 | Construction | -hygroscopic material -magnesium oxide |
369.OSM-HA |
| 22.33 | Construction | - electronic sensors in contact with water | OSM/HA 408 |
| 24 | Procedure | - Components | OSM/HA 230 |
| 25.9 and 25.13 | Detachable suplly cords | - Inlet opening | OSM/HA 431 |
| 25.15 | Detachable supply cords | - cord anchorage test - fixed appliances |
OSM/HA 399 |
| 25.15 | Heating and Abnormal Operation | - insulation of supply cord - table 3 a d 9 |
OSM/HA 400 |
| 25.22 | Connector | - Special connector | OSM/HA 165 |
| 25.23 | Internal conductors | - Accessible internal conductors | OSM/HA 54 |
| 26.5 | Terminals | - stranded conductors | OSM/HA 304 |
| 27.1 | Earthing | - ball bearing - reliable earth connection |
OSM-HA 380 |
| 27.1 | Provision for earthing | - crimping connection - protective conductor |
OSM-HA 419 |
| 27.2 | Earthing | - Snap-on connectors - Earth conitnuity |
OSM/HA 58 |
| 27.2 | Earthing | - pillar type terminals - pressure plate |
OSM/HA 59 |
| 27.4 | Earthing | - Protection against corrosion | OSM/HA 60 |
| 29.1 | Creepage/clearance | - printed circuit - distances on printed conductors |
OSM/HA 305 |
| 29.1.3 | Creepage/clearance | - working voltage - rated impulse voltag |
OSM-HA 423 |
| 29.2 | Creepage/clearance | - CTI - PCB |
OSM/HA 393 |
| 29.2 | Creepage/Clearance | - material groups | OSM/HA 441 |
| 29.3 | Distance | - thickness of solid insulation | OSM-HA 376 |
| 29.3.3 | Creepage/Clearance | - insulation of internal wiring | OSM/HA 444 |
| 30.2 | Glow-wire | - motor capacitor - glow wire test |
OSM-HA 378 |
| 30.2.2 and 30.2.3 | Glow-wire | - glow wire test | OSM-HA 381 |
| 30.2.3.1 | Glow wire test | - manufacturer declaration | 352.OSM-HA |
| 30.2.3.1 | Glow-wire | - current during normal operation - in rush current |
OSM-HA 384 |
| 30.2.3.2 | Needle flame test | - needle flame test - envelope of vertical cylindert |
OSM-HA 382 |
| EN 60335-2-02:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 2.2.9 | Normal operation | - Liquid dispensing pump | 0089.OSM-HA |
| 22.32 | Construction | - Deposition of dust | 0095.OSM-HA |
| EN 60335-2-03:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 2.2.10 | Definitions | - special purpose tools | 0001.OSM-HA |
| EN 60335-2-4: 2002 | |||
| Clause | Subject | Keywords | Sheet |
| 15.2 | Moisture resistance | - pouring test on top loaded appliancesl | 355.OSM-HA |
| 15.3 | Moisture resistance | - pouring test | 341.OSM-HA |
| EN 60335-2-05:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 19.101 | Abnormal operation | - Electronic defects | 0099.OSM-HA |
| B19.11.2 | Abnormal operation | -
Fault on electronic circuit - Interlock door |
0200.OSM-HA |
| EN 60335-2-05:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 19 | Abnormal operation | - interlock switches | OSM/HA 103 |
| 19.101 | Abnormal operation | - electronic defects | OSM/HA 99 |
| EN 60335-2-06:1999 | |||
| Clause | Subject | Keywords | Sheet |
| 20.101 | Stability | - Stability of cooking ranges | 0252.OSM-HA |
| EN 60335-2-06:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 3.1.6 | Definitions | - Diversity factor | 344.OSM-HA |
| 3.1.6 | Definitions | - diversity factor "F" - induction hob |
OSM-HA 385 |
| 3.1.9.101 | General conditions for the tests | - vessel dimension | 363.OSM-HA |
| 3.1.9.101 | Definitions | - non circular vessel - cooking zone |
OSM/HA 397 |
| 7.10 | Marking | - marking on push button - ON and OFF position |
OSM-HA 387 |
| 19.11, 19.11.1 and 19.11.2 | Abnormal operations | - | 370.OSM-HA |
| 19.11.2 | Abnormal operations | - fault conditions | OSM/HA 368 |
| 19.102 | Abnormal operation | - NTC - Thermal controls |
418.OSM-HA |
| 19.13 | Abnormal operation | - Pyrolytic self-clearning oven - Protective electronic circuits |
334.OSM-HA |
| 19.13 and 19.4 | Abnormal operation | - testing conditions | OSM/HA 433 |
| 21.102 | Mechanical strength | - Spring hammer test | 0317.OSM-HA |
| 24.1 | Components | - electronic controls | OSM/HA 410 |
| 32.101 | Radiation, toxicity and similar hazards | - pyrolytic oven | OSM/HA 446 |
| EN 60335-2-07:1990 | |||
| Clause | Subject | Keywords | Sheet |
| 19.101 | Abnormal operation | - Defects | 0114.OSM-HA |
| EN 60335-2-07:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 8 | Protection against electric shock | - Mechanical clamping means | 0113.OSM-HA |
| 15.2 | Moisture resistance | -
Time of operation - Water inlet valve |
0282.OSM-HA |
| 19 | Abnormal operation | - Interlock switches | 0116.OSM-HA |
| 19.11.2 | Abnormal operation | -
Fault on electronic circuit - Interlock door |
0201.OSM-HA |
| 19.101 | Abnormal operation | -
Fault on electronic board - Program position |
0312.OSM-HA |
| 27.1 | Earthing | -
Metal parts in contact with water - Earthing |
0122.OSM-HA |
| EN 60335-2-07:2001 | |||
| Clause | Subject | Keywords | Sheet |
| 2.2.9 | Normal load | - Definition of normal load | 0318.OSM-HA |
| EN 60335-2-7: 2002 | |||
| Clause | Subject | Keywords | Sheet |
| 11.7 | Heating | - worse load - most unfavourable |
OSM-HA 377 |
| 11.7.104 | Heating | - dry load | OSM-HA 375 |
| 15.2 | Moisture resistance | - pouring test | 342. OSM-HA |
| 15.2 | Moisture resistance | - pouring test on top loaded applicances | 356. OSM-HA |
| EN 60335-2-7: 2003 | |||
| Clause | Subject | Keywords | Sheet |
| 11.7 | Hearing | - worse load - most unfavourable |
OSM/HA 377 |
| 15.2 | Moisture resistence | - pouring test - appliances loaded from the top |
OSM/HA 356 |
| 19 | Abnormal operations | - Interlock switches | OSM/HA 116 |
| 19.101 | Abnormal operations | - defects | OSM/HA 114 |
| EN 60335-2-09:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 11 | Heating | - Pop corn makers | 0254.OSM-HA |
| EN 60335-2-9: 2003 | |||
| Clause | Subject | Keywords | Sheet |
| 11.8 | Heating | - limits of parts normally gripped - limits and testing specification |
OSM-HA 425 |
| 11.8 and 22.13 | Heating | - Knobs, handle - Touchable parts |
349.OSM-HA |
| 11.8 and Z.11.102 103 and 104 | Heating | - limits of parts normally gripped - limits and testing specification |
OSM-HA 424 |
| 19.13 | Abnormal operation | - Amount of gas | 350.OSM-HA |
| 22.106 | Construction | - heating element in fixed position | 371.OSM-HA |
| 22.108 | Construction | - test cloth - textile fabric |
OSM-HA 373 |
| 24.1 | Components | - electronic controls | OSM/HA 411 |
| EN 60335-2-10:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 2.2.9 | Normal operation | - Liquid dispensing pumps | 0128.OSM-HA |
| EN 60335-2-11:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 19.11.2 | Abnormal operation | -
Fault on electronic circuit - Interlock door |
0226.OSM-HA |
| 22.102 | Construction | - Built - in trumbler dryers | 0255.OSM-HA |
| EN 60335-2-11: 2002 | |||
| Clause | Subject | Keywords | Sheet |
| 15.2 | Moisture resistance | - pouring test | 343.OSM-HA |
| 15.2 | Moisture resistance | - pouring test on top loaded appliances | 357.OSM-HA |
| EN 60335-2-11: 2003 | |||
| Clause | Subject | Keywords | Sheet |
| 7.12 and 22.105 | Marking | - tumble dryer - cool down cycle |
OSM-HA 426 |
| 15.2 | Moisture resistance | - pouring test - appliances loaded from the top |
OSM/HA 357 |
| EN 60335-2-14:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 11 | Heating | - Kitchen machines with different accessories | 0319.OSM-HA |
| 20.2 | Mechanical hazards | -
Grain grinder - Accessibility to moving parts |
0303.OSM-HA |
| 20.2 | Mechanical hazards | - Application of the special test finger | 0315.OSM-HA |
| 20.103 | Mechanical hazards | -
Hemispherical test probe - Actuating members |
0257.OSM-HA |
| 20.104 | Mechanical hazards | -
Hemispherical test probe - Actuating members |
0257.OSM-HA |
| 20.109 | Mechanical hazards | -
Hemispherical test probe - Actuating members |
0257.OSM-HA |
| 20.115 | Mechanical hazards | -
Hemispherical test probe - Actuating members |
0257.OSM-HA |
| EN 60335-2-14:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 20.103 | Mechanical hazards | - milk whippers - cream whippers |
OSM-HA 374 |
| 20.106 | Mechanical hazards | - hopper - feed pusher |
360.OSM-HA |
| EN 60335-2-14:2006 | |||
| Clause | Subject | Keywords | Sheet |
| 20.103, 104, 109 and 115 | Mechanical hazards | - Hemispherical test probe | OSM/HA 257 |
| 20.106 | Mechanical hazards | - feed pusher - hopper |
OSM/HA 360 |
| 20.2 | Mechanical hazards | - Application of the special test finger | OSM/HA 315 |
| EN 60335-2-15:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 25.8 | Detachable supply cords | - Supply cords | 0239.OSM-HA |
| 15.2 | Moisture resistance | - Kettles | 0132.OSM-HA |
| 19.7 | Abnormal operation | - Espresso coffee makers | 0135.OSM-HA |
| 15.102 | Moisture resistance | - Spillage test | 0429.OSM/HA |
| EN 60335-2-15: 2002 | |||
| Clause | Subject | Keywords | Sheet |
| 15.102 | Moisture resistance | - Funnel tube | 337.OSM-HA |
| 25.8 | Detachable supply cords | - supply cords | OSM/HA 239 |
| EN 60335-2-17:1999 | |||
| Clause | Subject | Keywords | Sheet |
| 24.5 | Appliance inlet | -
Special appliance inlet - 4 poles appliance inlet |
0295.OSM-HA |
| EN 60335-2-17:2002 | |||
| Clause | Subject | Keywords | Sheet |
| 19.105 | Abnnormal operation | - folding test | 358.OSM-HA |
| EN 60335-2-21:1992 | |||
| Clause | Subject | Keywords | Sheet |
| 7.101 | Marking | -
Pull test - Inlet and outlet water hose |
0202.OSM-HA |
| 19.2/19.3 | Abnormal operation | - Test conditions for water heaters | 0203.OSM-HA |
| 19.2/19.3 | Abnormal operation | - Three phase water heaters | 0204.OSM-HA |
| EN 60335-2-21:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 7.101 | Marking | - pull test - inlet and outlet water hose |
OSM/HA 202 |
| 19.2/19.3 | Abnormal operation | - test conditions for water heaters | OSM/HA 203 |
| 19.2/19.3 | Abnormal operation | - three-phase water heaters | OSM/HA 204 |
| 24.102.2 | Components | -
operating temperature of thermal cut out - maximum water temperature |
OSM HA 412 |
| 22.106 | Construction | -
all pole disconnection - contactor |
OSM HA 392 |
| EN 60335-2-23:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 11.8 | Heating | - Curling rollers | 0313.OSM-HA |
| 30.101 | Needle flame test | - Needle flame test | 0270.OSM-HA |
| EN 60335-2-23: 2003 | |||
| Clause | Subject | Keywords | Sheet |
| 11.2 | Heating | - floor temperature for hair curler | OSM/HA 442 |
| 11.8 | Heating | -Curling rollers | OSM/HA 313 |
| 25.14 | Supply connection and external flexible cords | - Hair dryer - Flexibility test |
415.OSM-HA |
| 30.101 | Needle flame test | - Needle flame test | OSM/HA 270 |
| EN 60335-2-24:1994 | |||
| Clause | Subject | Keywords | Sheet |
| 25.3 | Appliance inlet | -
Connector - Locking of connector |
0146.OSM-HA |
| EN 60335-2-24: 2003 | |||
| Clause | Subject | Keywords | Sheet |
| 22.102 | Construction | - Insulated wire heaters - Joints |
333.OSM-HA |
| 22.112 | Construction | - Free space - Drawers |
345.OSM-HA |
| 24 | Components | - IEC 60079-15 | OSM-HA 383 |
| EN 60335-2-25:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 11 | Heating | -
Built-in microwave ovens - Lift-up doors - Door interlock |
0228.OSM-HA |
| 30.3 | Heat/fire/tracking | - Tracking test | 0155.OSM-HA |
| EN 60335-2-27:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 2.101 | Radiation, toxicity and similar hazard | - Exposure distance | 0221.OSM-HA |
| EN 60335-2-29:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 1 | Scope | - Accessible parts not SELV | 0300.OSM-HA |
| Annex ZA | Transformer | - Switching transformers | 0296.OSM-HA |
| EN 60335-2-29:2004 | |||
| Clause | Subject | Keywords | Sheet |
| 19.13 | Abnormal operation | - battery packs | OSM/HA 413 |
| 24.201 | Transformer | - Switching transformers | OSM/HA 296 |
| 30.2.3.1 and 30.2.3.2 | Heat/fire/tracking | - battery packs | OSM/HA 414 |
| EN 60335-2-30:1992 | |||
| Clause | Subject | Keywords | Sheet |
| 8.1 | Protection against electric shock | -
Fuel effect lamp - Removable covers |
0162.OSM-HA |
| 19.103 | Abnormal operation | - Felt strips | 0163.OSM-HA |
| 19.103 | Abnormal operation | - Heated mirror | 0167.OSM-HA |
| 30.51 | Heat/fire/tracking | - Substantially non metallic enclosure | 0166.OSM-HA |
| EN 60335-2-30:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 8.1 | Protection against electric shock | - Fuel effect lamp - Removable covers |
162.04.osm |
| 19.101 | Abnormal operation | -
Three phase room heaters - Thermal cut out |
0258.OSM-HA |
| 19.108 | Abnormal operation | Room air sensitive thermostat | 0321.OSM-HA |
| 25.7 | Detachable supply cords | PVC supply cable | 0314.OSM-HA |
| EN 60335-2-30:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 5 | General conditions for the tests | - family/series of stationary radiant room heaters | OSM-HA 388 |
| 8 and 20 | Protection against electric shock | - enclosure of plastic material - portable fan heater |
OSM/HA 192 |
| 8.1 | Protection against electric shock | - fuel effect lamp - removable covers |
OSM/HA 162 |
| 11.8 | Heating | - limits for metal enclosures | 364.OSM-HA |
| 19.11.4 and 22.109 | Construction | - stand by mode | OSM/HA 434 |
| 19.103 | Abnormal operation | - felt strips | OSM/HA 163 |
| 19.103 | Abnormal operation | - Heated mirror | OSM/HA 167 |
| 22.10 | Construction | - non self resetting thermal cuttout | OSM/HA 435 |
| 22.109 | Construction | - electronic switch | OSM/HA 445 |
| 25.7 | Detachable supply cords | - PVC cable - surfaces temperature rise |
OSM/HA 314 |
| 30.101 | Heat/fire/tracking | - substantially non metallic enclosure | OSM/HA 166 |
| EN 60335-2-31:1990 | |||
| Clause | Subject | Keywords | Sheet |
| 19.101 | Abnormal operation | - Supply voltage | 0170.OSM-HA |
| EN 60335-2-31:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 7.12.1 | Instructions | - distance from the gas hob surfaces | 0306.OSM-HA |
| EN 60335-2-31:2002 | |||
| Clause | Subject | Keywords | Sheet |
| 30.101 | Needle flame test | -
air stream - carbon filter - grease filter |
365.OSM-HA |
| EN 60335-2-31:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 7.12.1 | Instructions | - distance from the gas hob surfaces | OSM/HA 306 |
| 19.101 | Abnormal operation | - supply voltage | OSM/HA 170 |
| EN 60335-2-32:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 24.2 | Components | - switches and controls on flexible cables | OSM/HA 443 |
| EN 60335-2-35:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 19.4 | Abnormal operation | - testing specification | OSM/HA 440 |
| EN 60335-2-40:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 15.4 | Spillage test | - application of 75 mm diameter glass | 0323.OSM-HA |
| EN 60335-2-53:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 30.3 | Heat/fire/tracking | -
Control units - Sauna appliances |
0260.OSM-HA |
| EN 60335-2-54:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 20.101 | Mechanical hazards | -
Cylindrical test rod - Switch |
0261.OSM-HA |
| EN 60335-2-54: 2003 | |||
| Clause | Subject | Keywords | Sheet |
| 20.101 and 22.103 | Mechanical hazards | - Inadvertent operations - Pressurised stream |
346.OSM-HA |
| EN 60335-2-55:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 22.6 | Construction | - Submersible aquarium heaters | 0264.OSM-HA |
| EN 60335-2-55:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 3.1.9 | Definitions | -
aquarium heaters - normal operation |
OSM/HA 394 |
| EN 60335-2-56:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 11.8 | Heating | - Temperature rise of lenses | 0242.OSM-HA |
| 11.8 | Heating | - Lenses | 0265.OSM-HA |
| EN 60335-2-59:1994 | |||
| Clause | Subject | Keywords | Sheet |
| 1 | Scope | - Insect catcher with adhesive paper | 0222.OSM-HA |
| 24.1 | Transformer | - High voltage transformer | 0178.OSM-HA |
| EN 60335-2-60:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 15.1.2 | Moisture resistance | -
Integral parts - IPX5 |
0266.OSM-HA |
| EN 60335-2-60: 2003 | |||
| Clause | Subject | Keywords | Sheet |
| 19.11 | Abnormal operation | - Telephone set - Accessibility |
347.OSM-HA |
| 22.33 | Construction | - PTS for shower cabinets - Accessibility |
348.OSM-HA |
| EN 60335-2-61:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 24.101 | Components | -
Thermal cut out - Thermal storage heaters |
0286.OSM-HA |
| EN 60335-2-61:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 24.101 | Components | - Thermal cut out - Thermal storage heaters |
OSM/HA 286 |
| EN 60335-2-69:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 19.101 | Abnormal operation | - overflow test | 366.OSM-HA |
| EN 60335-2-71:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 11 | Heating | - IR lamps | 0213.OSM-HA |
| EN 60335-2-71:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 11.7.104 | Heating | - IR lamps | OSM/HA 213 |
| EN 60335-2-75:2002 | |||
| Clause | Subject | Keywords | Sheet |
| 1 | Standard / Scope | - water dispensers | 351.OSM-HA |
| 22.6 | Construction | -
Syringe test - Tubes of elastomeric material - Annex AA |
0311.OSM-HA |
| EN 60335-2-80:1997 | |||
| Clause | Subject | Keywords | Sheet |
| 30 | Heat/fire/tracking | -
Duct fans - Needle flame test |
0223.OSM-HA |
| EN 60335-2-80:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 21.101 | Mechanical strength | -
using of the test finger - mechanical resistance of the grid |
OSM-HA 386 |
| EN 60335-2-82:2001 | |||
| Clause | Subject | Keywords | Sheet |
| 1 | Scope | - components
in the scope of EN 60065 or EN 60950 |
0324.OSM-HA 324.04.OSM |
| EN 60335-2-89:2002 | |||
| Clause | Subject | Keywords | Sheet |
| 15.103 | Moisture resistance | - small volume refrigerators | 361.OSM-HA |
| EN 60335-2-101:2002 | |||
| Clause | Subject | Keywords | Sheet |
| 11.8 | Heating | -
definition of the term "grids" |
0325.OSM-HA |
| 19.101 | Abnormal operation | - Covering
test - Wrapped cotton sheet |
0326.OSM-HA |
| EN 60598-1 All Editions | |||
| Clause | Subject | Keywords | Sheet |
| 0.4 | Luminaires needing assembly by the user | - Internal wiring - STRF - Pole brackets |
401.06osmlum |
| 0.5 | Components | - European standard - Components - National standard |
402.06osmlum |
| 0.5 | Lumianires provided with socket - outlets | - ENEC Agreement - Socket - outlets - ENELC mark |
403.06osmlum |
| 4.11.2 7.2.1 |
Earthing continuity | - National approval mark - Certification Body - 34D/784/CD |
406.06osmlum |
| EN 60598-1/2000 | |||
| Clause | Subject | Keywords | Sheet |
| 2.4 - 3.2.7, 3.2.9 - 3.3.4 |
F-marking on recessed luminaires | - Marking - Type reference - Mounting instruction |
405.06osmlum |
| 4.15 - 12.7 12.7.1 |
Measurement of luminaire enclosure; application of § 12.7.1 | - IS 07 - ISO 75 test - Ball pressure test |
407.06osmlum |
| EN 60598-1/2004 | |||
| Clause | Subject | Keywords | Sheet |
| 1.2.60 | T5 adapter | - Semi-luminaire - ENEC mark - G13 / G5 |
404.06osmlum |
| 5.2.14 Annex ZB |
Portable luminaire | - Cable reel - IP rated sockets - BS 1363 |
408.06osmlum |
| EN IEC 60598-1/2003 A1:2006, EN 60598-1 /2004 A1/2006 | |||
| Clause | Subject | Keywords | Sheet |
| General 1.2.60 2.2 | T8 to T5 , T8 to T8 and similar lamp adaptors (including ditto with LED) | - Retro-fit conversion units - Semi-luminaires - Lamp adaptors |
702.08osmlum |
| EN 60598-1/2004 | |||
| Clause | Subject | Keywords | Sheet |
| 1.2.60 | T5 adapter | - Semi-luminaire - ENEC mark - G13 / G5 |
404.06osmlum |
| EN 60598-1/2004 | |||
| Clause | Subject | Keywords | Sheet |
| 1.2.60 | T5 adapter | - Semi-luminaire - ENEC mark - G13 / G5 |
404.06osmlum |
| IEC/EN 60598-1, IEC/EN 60968, IEC/EN 60061, IEC/EN 62031, IEC/EN 62471, IEC TR 62471-2 Last Editions | |||
| Clause | Subject | Keywords | Sheet |
| General | Self-ballasted LED lamps | - LEDs - Self-ballasted lamps - Standard -Data Sheet / Lamp cap |
PDSH xxxx |
| General | LEDs used as a light source in luminaires | - LEDs - Harmful radiation - Low luminance - Hazard risk classification |
PDSH YYYY |
| Section 12 | Luminaires provided with LEDs | - LEDs / LED modules - Thermal tests - Luminaires Class I / II / III |
PDSH ZZZZ |
| IEC/EN 60598-1, IEC/EN 62471 IEC TR 62471-2, Last Editions | |||
| Clause | Subject | Keywords | Sheet |
| General | LEDs used as a light source in luminaires | - LEDs - Harmful radiation - Low luminance - Hazard risk classification |
PDSH 0744 |
| IEC/EN 60598-1, IEC/EN 60598-2-6, IEC/EN 62031, IEC/EN 62471, IEC TR 62471-2, Last Editions | |||
| Clause | Subject | Keywords | Sheet |
| Section 12 | Luminaires provided with LEDs | - LEDs / LED modules - Thermal tests - Luminaires Class I / II / III |
PDSH 0745 |
| EN 60598-2-2/1996 and A1/1997 | |||
| Clause | Subject | Keywords | Sheet |
| 2.4 - 3.2.7, 3.2.9 - 3.3.4 | F-marking on recessed luminaires | - Marking - Type reference - Mounting instruction |
405.06osmlum |
| EN 60598-2-5/1998 and Ec/1998 | |||
| Clause | Subject | Keywords | Sheet |
| General | Floodlight with special lamp | -
Instructions - Manufacturer - 2000 W, K12, 5x7sMN |
410.06.osmlum |
| EN 60669-1:1999 + A1:2002 | |||
| Clause | Subject | Keywords | Sheet |
| 12.2.1 (table 2) | Terminal connecting capacity for for rated current up to 4 A | - Terminals | OSM-IN 223 |
| 13.12 | Inlet opening of surface-type switches | - Inlet opening | OSM-IN 238 |
| 13.2 | Correct positioning of conductors | - Correct positioning | OSM-IN 239 |
| 18 - 19 | Simplification of making and breaking capacity and normal operation tests | - Simplification | OSM-IN 240 |
| 18.2 – 19.2, 18 – 19.102, 18 – 19 | Sticking of the contacts | - Sticking - Welding | OSM-IN 231 |
| 20.4.1 | Verification of non-removal of covers, cover plates or actuating members | - Non-removal | OSM/IN 241 |
| 24 | Resistance of insulating material to abnormal heat and to fire | - Glow-wire -Insulating material -Retain current-carrying part |
OSM/IN 209 |
| EN 60669-2-1:2000 | |||
| Clause | Subject | Keywords | Sheet |
| 19 (Fig. 14) | Values of capacitor C1 for switches with rated current lower than 6 A | - Capacitor C1 | OSM-IN 224 |
| 101.1.1.2 | Testing of electronic switches without incorporated fuses/without incorporated temperature-limiting devices | - Electronic switches - Fuses - Temperature - limiting devices |
OSM-IN 225 |
| EN 60669-2-1:2004 | |||
| Clause | Subject | Keywords | Sheet |
| 17 (table 102) | - Temperature rise on cover surfaces of a dimmer switch - Use of standardized boxes for the temperature rise test |
- Cover sufaces -Box |
OSM-IN 215 |
| 18.2 – 19.2, 18 – 19.102, 18 – 19 | Sticking of the contacts | - Sticking - Welding |
OSM-IN 231 |
| 23 | Electronic switch multi-layer printed wire board creepage and clearance distances | - multi-layer printed wire board -creepage -clearance |
OSM-IN 216 |
| 101.1.1.2 | Testing of electronic switches without incorporated fuses/without incorporated temperature-limiting devices | - Electronic switches - Fuses - Temperature - limiting devices |
OSM-IN 226 |
| EN 60670-1:2005 | |||
| Clause | Subject | Keywords | Sheet |
| 12.1.2.4 | Definition of “reverse tapers” | - Reverse tapers | OSM-IN 233 |
| 13.3.4 | Positioning of the dry absorbent paper and the strip of paper for IP tests | - Dry absorbent paper - Protected volume - Strip of paper |
OSM-IN 230 |
| 15.3 | Impact test on boxes provided with knock-outs | - knock-outs | OSM/IN 250 |
| EN 60730-1/1995 | |||
| Clause | Subject | Keywords | Sheet |
| 17.2.2.+17.7.6 | Over voltage test | Over voltage test | 067.OSM-IN |
| General | Identification of materials of construction | Identification | 071.OSM-IN |
| 2.4.3 + 2.4.5 |
"OFF" Marking on electronic controls | Marking | 072.OSM-IN |
| 6.2.3 & Table 17.2.1 | Circuit for declared specific load | Specific load | 073.OSM-IN |
| 7 | Printed leaflet or specification sheet | Printed leaflet | 074.OSM-IN |
| Table 10.1.4 | Interpretation of the upper limits | Upper limits | 075.OSM-IN |
| 10.1.8 (fig. 10 and 11) |
Dimension "e" on clamping screw terminals | Dimension | 076.OSM-IN |
| 10.2.4 (fig. 14&15) 1 | Dimensional requirements for for flat push-on terminals | Dimension | 077.OSM-IN |
| 14.1 | Maximum temperature in terminals of T-marked controls. | temperature in terminals | 078.OSM-IN |
| Table 14.1 | Maximum temperature permitted for .on Table 14.1 for materials used other than for wires | Maximum temperature | 079.OSM-IN |
| 14.5.2 17.3.1 |
T-marked independently mounted controls. | T-marked | 080.OSM-IN |
| 14.7.1 | Current-carrying parts made of copper or brass. | Current-carrying parts | 081.OSM-IN |
| 17.2.217.2.2 | Clarification of the interpretation of the standard. | Clarification of the interpretation | 082.OSM-IN |
| 17.3.1 | Additional tests for automatic electrical controls with Tmax below 0 șC | automatic electrical controls | 083.OSM-IN |
| 19.2.3 | Suitability of non-metallic material through which contact pressure is transmitted. | Suitability of non-metallic material | 084.OSM-IN |
| H23 | Clarification of the Standard text | Clarification | 086.OSM-IN |
| H26 | Electronic controls declared as "no protection" according table 7.1 item 58 a | Electronic controls | 087.OSM-IN |
| EN 60730-1:2000 + A1:2004 + A12:2003 + A13:2004 + A14:2005 + A15:2007 + A16:2007 | |||
| Clause | Subject | Keywords | Sheet |
| H.2.7.14 H.11.2.5 Table H.21.71 |
Capacitors used for protective impedance | Protective impedance | OSM-IN 210 |
| 14 | Behaviour of a protection device during heating test | - heating | OSM/IN 251 |
| EN 60730-2-3:1992 | |||
| Clause | Subject | Keywords | Sheet |
| 20.101 | Creepage distances and clearances across micro-interruption | Creepage distances and clearances | 065.OSM-IN |
| EN 60730-2-4:1993 | |||
| Clause | Subject | Keywords | Sheet |
| 20.101 | Creepage distances and clearances across micro-interruption | Creepage distances and clearances | 066.OSM-IN |
| EN 60730-2-7:1991 | |||
| Clause | Subject | Keywords | Sheet |
| 17.1.3.101 | Over voltage test | Over voltage test | 067.OSM-IN |
| EN 60730-2-8:1995 | |||
| Clause | Subject | Keywords | Sheet |
| Appendix BB | Interpretation of item 9 of the arrangement for measurement of transient pressure caused by electrovalves | Interpretation | 068.OSM-IN |
| EN 60730-2-9:2002 + A1:2003 + A11:2003 + A12:2004 + A13:2004 + A2:2005 | |||
| Clause | Subject | Keywords | Sheet |
| 7.16.104 | Connection of the electrical test lead to mannual reset thermal cut-outs | Manual reset | OSM-IN 211 |
| EN 60730-2-10:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 14.4 (1) | Heating test | Heating test | 069.OSM-IN |
| 17 | Motor starting relays test arrangements | Relays | 070.OSM-IN |
| EN 60799:1998 | |||
| Clause | Subject | Keywords | Sheet |
| General | CCA-NTRs for cord sets | - Cord set, - Plug, - Cord, - Coupler |
OSM-IN 203 |
| EN 60838-1/2004 | |||
| Clause | Subject | Keywords | Sheet |
| General | Miscellaneous lampholder ENEC certification | -
ENEC Group - Gauges - FDIS documents |
411.06.osmlum |
| EN 60921 and EN 60923 all editions | |||
| Clause | Subject | Keywords | Sheet |
| General | ENEC mark on ballast | -
Data sheet - ENEC mark/ballast - Lamp manufacturer |
414.06.osmlum |
| EN 60947-3:1999 | |||
| Clause | Subject | Keywords | Sheet |
| 8.2.5.2 | Test forces for actuators | Test forces | 094.OSM-IN |
| EN 60950 | |||
| Please click here in order to access sheets for IEC 60950:1999 & IEC 60950-1:2000, EN 60950, EN 60950:2000, EN 60950:2000 & EN 60950-1:2001, EN 60950-1:2001, EN 60950-1:2001 & EN 60950-1:2006 IEC/EN 60968, IEC/EN 60061, IEC/EN 62031, IEC/EN 62471, IEC TR 62471-2, Latest Editions, pr/IEC 62560 guidance only) | |||
| Clause | Subject | Keywords | Sheet |
| General | Self-ballasted LED lamps | - LEDs - Self-ballasted lamps - Standards - Data Sheet / Lamp cap |
PDSH 0743 |
| EN 60898-1:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 9.12.11.2.2 | Test voltage | - test voltage - IT systems |
OSM/IN 247 |
| 9.14 | Resistance to abnormal heat andto fire (glow-wire test) | Glow-wire test | OSM/IN 218A |
| EN 61008:1994 | |||
| Clause | Subject | Keywords | Sheet |
| 9.21.1.4 | Clarification of the text | - pulsating direct current - smooth direct current |
OSM/IN 207 |
| Annex A | Testing of RCCB's of different classification due to behaviour to DC components | RCCB's | 101.OSM-IN |
| EN 61008-1:2004 | |||
| Clause | Subject | Keywords | Sheet |
| 9.14 | Resistance to abnormal heat andto fire (glow-wire test) | Glow-wire test | OSM/IN 218A |
| 9.21.1.4 | Clarification of the text | - pulsating direct current - smooth direct current |
OSM/IN 207 |
| EN 61008-2-1:1994 | |||
| Clause | Subject | Keywords | Sheet |
| 9.23 | Verification of ageing of electronic components. | ageing | 103.OSM-IN |
| EN 61009-1:1994 | |||
| Clause | Subject | Keywords | Sheet |
| 9.21.1.4 | Clarification of the text | - pulsating direct current - smooth direct current |
OSM/IN 208 |
| 9.9.2.2 | Test of instantaneous tripping and of correct opening of the contacts | - Instantaneous tripping | OSM/IN 214A |
| G.3.2 (Annex G) | Marking of RCBO's | Marking of RCBO's | 106.OSM-IN |
| G.4.1 (Annex G) | Constructional requirements | Constructional | 107.OSM-IN |
| G.4.3 (Annex G) | Mechanical requirements | Mechanical requirements | 108.OSM-IN |
| G.4.4 a) b) + c) (Annex G) | Electrical compatibility | Electrical compatibility | 109.OSM-IN |
| G.4.4. d) (Annex G) | Uniform interpretation of sub-clause G.4.4.d) | Uniform interpretation | 111.OSM-IN |
| EN 61009:2004 | |||
| Clause | Subject | Keywords | Sheet |
| 9.15 | Resistance to abnormal heat andto fire (glow-wire test) | Glow-wire test | OSM/IN 218A |
| 9.21.1.4 | Clarification of the text | - pulsating direct current - smooth direct current |
OSM/IN 208 |
G.4.1 – G.5.4 (Annex G) |
Missing requirements for r.c. units declared not suitable for disassembling | - r.c. unit; -disassembling |
OSM/IN 245 |
| G.5.3 (Annex G) | Inconsistency regarding the test current In instead of 1,13 In | - test current | OSM/IN 246 |
| EN 61009-2-1:1994 | |||
| Clause | Subject | Keywords | Sheet |
| G.3.2 (Annex G) | Marking of RCBO's | Marking of RCBO's | 106.OSM-IN |
| G.4.1 (Annex G) | Constructional requirements | Constructional | 107.OSM-IN |
| G.4.3 (Annex G) | Mechanical requirements | Mechanical requirements | 108.OSM-IN |
| G.4.4 a) b) + c) (Annex G) | Electrical compatibility | Electrical compatibility | 109.OSM-IN |
| G.4.4. d) (Annex G) | Uniform interpretation of sub-clause G.4.4.d) | Uniform interpretation | 111.OSM-IN |
| EN 61058-1:1992 | |||
| Clause | Subject | Keywords | Sheet |
| General | Sample selection for test on homogeneous series of switches | Sample selection | 112b.OSM-IN |
| 11.1.2.1.4 | Terminals for prepared copper conductors requiring the use of special purpose tool | prepared copper conductors | 118.OSM-IN |
| 16 + 17 | Flat quick-connect terminations | Flat quick-connect | 119.OSM-IN |
| 17.1.2 17.2.1.2 |
Test voltage | Test voltage | 120.OSM-IN |
| 19.2 | Suitability of non-metallic material through which contact pressure is transmitted | non-metallic material | 122.OSM-IN |
| EN 61058-1:1995 | |||
| Clause | Subject | Keywords | Sheet |
| 17.2.1.2 | Over voltage test | Over voltage test | 121.OSM-IN |
| EN 61058-1:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 3.5.102 | Fixing of the housing of non-rewirable switches | Fixing | 125.OSM-IN |
| EN 61058-1:2002 | |||
| Clause | Subject | Keywords | Sheet |
| 7.1.3.2, 7.1.3.3, 16.3.2, (Table 13) | T-marking and heating test | T-marking | OSM-IN 229 |
| 7 – 8 – 17 | Rotary switches for “cooking range" (Classification and endurance test specifications) | - cooking range switch - multiple poles |
OSM/IN 242 |
| 13 – 17 | Rotary switches for “cooking range" (endurance test) | - cooking range switch - multiple poles |
OSM/IN 243 |
| EN 61058-2-1:1993+A1:1996 (+A11:2002) A1:1996 | |||
| Clause | Subject | Keywords | Sheet |
| 3.5.102 | Fixing of the housing of non-rewirable switches | - Fixing - Housing |
OSM/IN 235 |
| 12.3 | Type of attachment of flexible cords | - Attachment - Connection |
OSM/IN 234 |
| 12.3.101, 12.3.107 | Pull test and following torque test on non-rewirable switches | - Pull test, - Torque test |
OSM/IN 236 |
| 12.3.107 + 12.3.110 and A1 | Pull testing and following torque test of non-rewirable switches | Pull testing | 126.OSM-IN |
| EN 61347-2-3/2001 + A1/2004 + A2/2006 | |||
| Clause | Subject | Keywords | Sheet |
| General | Uncased ballasts, convertors | -
Mandatory markings - EN 61347-2-3 - Label/ ballast |
412.06osmlum |
| 7.2 | Working voltage measurement | -
Working voltage - Terminals - Earth |
413.06osmlum |
| EN 61347-2-8/2001 + A1/2006 | |||
| Clause | Subject | Keywords | Sheet |
| General | ENEC mark on ballast | -
Data sheet - ENEC mark/ballast - Lamp manufacturer |
414.06.osmlum |
| EN 61386-21:2004 | |||
| Clause | Subject | Keywords | Sheet |
| General | Testing programme for a range of conduits sizes | -
Conduit - Size |
OSM-IN 227 |
| EN 61386-21:2004,EN 61386-22:2004, EN 61386-23:2004 | |||
| Clause | Subject | Keywords | Sheet |
| General | Certification procedure for conduits and conduit fittings | -
Conduit - conduit fittings |
OSM-IN 237 |
| EN 61534:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 3.23 (Table 20) | Classification of socket-outlet used in combination with power track system | - Power track system - Classification - Temperature rise |
OSM-IN 232 |
| EN 61643-11:2002 + A11:2007 | |||
| Clause | Subject | Keywords | Sheet |
| General | Issue of a CCA-STR for a plug in surge protector within CCA Agreement | - Surge protector - Plug - Socket-outlet |
OSM/IN 204 |
| 6.1.1 q) | Markings | - marking - frequency |
OSM/IN 213 |
| 7.5 a) 7.5.4 a) |
Measured limiting voltage | - measured limiting voltage - protection level - energies testing |
OSM/IN 212 |
| EN 62208:2003 | |||
| Clause | Subject | Keywords | Sheet |
| 9.6 | Impact test in knock-outs | - Knock-outs | OSM-IN 219 |
- IECEE. Taking Conformity Assessment Further
- Copyright © IEC-IECEE 2010